What goes in a cut list?

Each row is one kind of part: a label, the material, the thickness, the length and width, the quantity and whether the part may be turned a quarter turn. Add a grain note for veneered or visible-grain panels. Keep the unit written beside the number.

One row per kind of part
FieldWhy it matters
LabelLets you find the piece on the layout and mark it after cutting
Material and thicknessParts only come from stock of the same material and thickness
Length × widthFinished size, after joints and edge treatment are allowed for
QuantityCounts every copy so none is dropped
Grain / rotationDecides whether a part can be turned to fit

Decide what length means before you write the first row. A common choice is that length is the dimension the grain runs along. Then a grain-locked part's length always points along the sheet's grain, and anyone reading the list knows which edge is which. Write that convention at the top of the list.

A cut list is different from a materials list. A materials list says what to buy. A cut list says what each piece must measure and how many you need. You usually write the cut list first and derive the materials from it. Hardware such as screws, hinges and edge banding belongs in a separate list.

How do I turn a drawing into part sizes?

Work from the finished assembly. Subtract the thickness of any part that sits between two others, and subtract the depth of any groove or rabbet that takes a back panel. Write the size the part must have when it leaves the saw. If you plan to band an edge, subtract the band thickness from that side.

part between two sides = outside width − side thickness − side thickness600 − 18 − 18 = 564 mm

Example: a cabinet 600 mm wide outside, with 18 mm sides, has 564 mm between the sides, so a top, bottom or fixed shelf that sits between them is 564 mm long. Change the side thickness and the shelf changes with it. That is why thickness belongs on every row: if you switch from 18 mm to another thickness, every part that sits between the sides has to be recalculated.

Write down how each part meets its neighbours before you size it. Does the top sit on the sides or between them? Does the back overlay the back edges or sit in a rabbet? Each answer changes a number. If you do not know yet, the cut list is not ready, and guessing here is how parts end up short.

If you band edges, look up or measure the thickness of the banding you will use and subtract it from each banded edge. The edge banding allowance guide and the solid wood edging guide work through the arithmetic.

Worked example: a cut list for a small open shelf unit

Drawing: an open box 600 mm wide, 720 mm tall and 300 mm deep, in 18 mm plywood. Sides run full height. Top and bottom sit between the sides. One fixed shelf sits between the sides, set 20 mm back from the front. The back is a 6 mm panel fixed over the back edges. No edge banding.

Worked example: working out each size

Sides: full height and depth, 720 × 300 mm.

Top and bottom: between the sides, 600 − 18 − 18 = 564 mm long, full depth 300 mm.

Shelf: 564 mm long, depth 300 − 20 = 280 mm.

Back: overlays the whole back, 720 × 600 mm, in 6 mm material.

Finished cut list (mm, length is the grain direction)
LabelMaterialLength × widthQtyRotate?
SidePlywood 18720 × 3002No
Top/BottomPlywood 18564 × 3002No
ShelfPlywood 18564 × 2801No
BackPlywood 6720 × 6001Yes, if the back's face is not on show

The 18 mm parts total 2 × 720 × 300 + 2 × 564 × 300 + 564 × 280 = 928,320 mm², about 0.93 m². That is a quick check that they belong on one sheet, not a layout. Only the planner, with kerf and grain, can tell you whether they actually fit. For a larger example, see the bookcase cut list from one sheet.

How do I list the stock I have?

Measure the sheets and boards you own or will buy. Use the usable size after you trim a rough or damaged edge, not the label on the product. Group stock by material and thickness, because a part can only come from matching stock. See plywood sheet sizes and nominal versus actual lumber sizes.

List offcuts you already have before new sheets, so the plan tries them first. What offcuts to keep covers which leftovers are worth entering. If you have no stock yet, start with one full sheet or board and let the plan tell you whether you need more. How many sheets of plywood do I need? explains the estimate.

A stock list for the example
StockMaterialMeasured size (mm)Qty
Offcut BP-12Plywood 18560 × 3031
Full sheetPlywood 18Measure yours1
Half sheetPlywood 6Measure yours1

Where does the kerf go?

The blade removes a strip of material at every cut, so two parts cut side by side from one board never add up to the board's length. Enter your measured kerf once for the job. Measure your saw kerf with a test cut instead of guessing.

Worked example: two parts from one length

Two top/bottom parts at 564 mm from a 1200 mm length, kerf 3 mm (an assumed value for this example).

564 + 3 + 564 = 1131 mm used. A second cut to free the second part from the rest takes another 3 mm: 1131 + 3 = 1134 mm, leaving 1200 − 1134 = 66 mm.

Do not add the kerf to part sizes in the list. The list holds finished sizes, and the planner adds the kerf between parts. Adding it twice makes every part too big.

How do I mark grain and rotation?

For each row, decide whether the part may be turned a quarter turn. A part with visible face grain usually may not, because turning it makes the grain run the wrong way. A painted part, a hidden back or an unpatterned MDF panel usually may, and allowing it gives the planner more ways to fit parts. Kerflio honours no-rotate per part. See grain and rotation.

If drawer fronts or doors need their grain to flow from one to the next, note that separately. Grain matching is a visual choice the planner does not make for you.

What should I check before cutting?

  • Counts: requested equals placed plus unplaced. Kerflio shows all three.
  • Units: every number in the same unit, fractions converted. See fractions and units.
  • Grain: no part turned where the face pattern must run one way. See grain and rotation.
  • Stock: enough sheets or boards, with the usable size you measured.
  • Order: cut the largest parent pieces first, then subdivide. See cutting order for sheet goods.

Then read the diagram once, label by label, as described in how to read a cutting diagram. The common mistakes are a part sized as if it sat on the sides when it sits between them, a thickness changed in one row but not in the parts that depend on it, and a fraction typed as a decimal by mistake.

Can I enter the list in Kerflio?

Yes. The sheet planner and linear planner on this website take up to 12 pieces and run in your browser. The Android app takes larger jobs and imports a CSV file, described in the CSV format guide.

The free plan in the app covers up to 12 pieces and 2 saved projects. A one-time full access purchase raises that to 150 pieces and 1,000 saved projects. There is no subscription and no account. For how the planner arranges parts, see what a cut list optimizer does, and browse all workshop notes for more.

Frequently asked questions

Is a cut list the same as a materials list?

No. A materials list says what to buy. A cut list says what each piece must measure and how many you need. You usually write the cut list first and derive the materials from it.

Do I list hardware?

Not in the cut list. Keep screws, hinges and edge banding in a separate list.

Should part sizes include the saw kerf?

No. Write finished sizes and enter your measured kerf once in the planner, which adds it between parts.

Which dimension is the length?

Pick a convention and write it on the list. A common one is that length runs along the grain, which keeps grain-locked parts easy to read.

How many parts can I plan for free?

The web planners and the free plan in the Android app take up to 12 pieces. Full access in the app takes up to 150.

How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.