What does rotation mean in a cut plan?
Rotation is a quarter turn of a part on the sheet. A 700 × 500 mm part can sit with its 700 mm side along the sheet's length, or turned so the 500 mm side runs that way. The part is the same size either way, but it lines up differently with the grain, and it fits differently next to its neighbours.
Rotating a rectangle changes which side follows the stock. For wood grain, veneer or a printed pattern, that orientation can matter as much as the dimensions. Allowing rotation gives a planner more arrangements to try. Locking it removes options, and sometimes those options were the ones that saved a sheet.
Length and width need a consistent meaning
Imagine a shelf panel listed as 600 mm long and 250 mm wide. If the grain needs to run along the 600 mm edge, that direction belongs in the part's requirements. The planner cannot infer it from a label such as "shelf".
On a sheet with grain running along its long edge, a quarter turn changes the grain relationship. In the web planner, the rotation checkbox permits a quarter turn; leave it off when the orientation shown by your dimensions must stay fixed. Kerflio honours a no-rotate setting per part, so you can lock the visible parts and let the hidden ones turn.
A simple convention keeps a list readable: write each part with the grain along its length, so a 720 × 560 mm cabinet side has grain running along 720 mm. Then grain direction and length always mean the same thing.
When may a part rotate?
| Part | Rotate? | Why |
|---|---|---|
| Plain MDF, any part | Usually yes | No wood grain on the face |
| Plain-colour melamine or painted parts | Usually yes | No pattern to line up |
| Plywood parts hidden inside a carcass, such as drawer bottoms or backs that will not show | Often yes | Appearance does not matter; check strength needs |
| Visible veneered plywood: sides, doors, drawer fronts | No | Grain direction shows |
| Woodgrain-printed melamine or laminate | No | The printed grain has a direction |
| Visible plywood shelves | Usually no | The front edge and face show the grain |
These are planning defaults, not rules for every project. When in doubt, lock the part; a locked plan that uses an extra sheet is cheaper than a visible part with the grain the wrong way. For cabinet-specific choices, read plywood grain direction for cabinets.
How much can locking grain cost? A worked example
Take fourteen identical parts, 700 × 500 mm, from 1,220 × 2,440 mm sheets with grain along the 2,440 mm length and a 3 mm kerf.
Each part keeps its 700 mm side along the sheet's length.
Across the 1,220 mm width: 500 + 3 + 500 = 1,003 mm, so two parts. A third would need 1,506 mm.
Along the 2,440 mm length: 700 + 3 + 700 + 3 + 700 = 2,106 mm, so three parts. A fourth would need 2,809 mm.
2 × 3 = 6 parts per sheet. Fourteen parts need 6 + 6 + 2: three sheets.
Split the sheet's width into two strips running the full length: one 700 mm wide and one 500 mm wide. 700 + 3 + 500 = 1,203 mm, which fits in 1,220 mm.
In the 700 mm strip the parts are turned: 500 mm along the length. Four fit: 4 × 500 + 3 × 3 = 2,009 mm.
In the 500 mm strip the parts stay upright: 700 mm along the length. Three fit: 3 × 700 + 2 × 3 = 2,106 mm.
4 + 3 = 7 parts per sheet. Fourteen parts need exactly two sheets.
The Kerflio planning engine returns the same result for both settings: three sheets at 54.9% material use with the grain locked, two sheets at 82.3% with rotation allowed. The percentages follow from the areas: 14 × 0.35 m² = 4.9 m² of parts, against 3 × 2.977 m² or 2 × 2.977 m² of sheet.
What if only some parts are locked?
Mixed lists are common: cabinet sides locked, internal shelves free. In the pattern above, every sheet has room for three upright parts in its 500 mm strip. So a sheet can carry up to three grain-locked parts plus four free ones.
Sheet 1: three locked parts in the 500 mm strip, four free parts turned in the 700 mm strip. 7 parts.
Sheet 2: one locked and two free parts in the 500 mm strip, four free parts turned in the 700 mm strip. 7 parts.
Total 14 parts on two sheets, worked out by hand.
A heuristic planner, Kerflio included, does not try every arrangement and may return three sheets for a mixed list like this. If a result uses more sheets than you expect, sketch the strips by hand and compare. You can also try moving parts between locked and free, or splitting the list into two runs. The methodology page explains why the search does not promise the fewest sheets.
Plywood, MDF and melamine: what changes?
Plywood has a face veneer with a visible grain, and each layer runs at right angles to the next. The face grain direction is part of the material, and it can run along or across the sheet; the plywood sheet sizes guide covers long-grain and cross-grain panels.
MDF has no grain on its face. The Composite Panel Association describes its surface as flat, smooth, uniform, dense and free of knots and grain patterns. Unless the part will be veneered later with a directional face, rotation is usually fine.
Source: Composite Panel Association, MDF, checked 2026-11-14.
Melamine-faced board depends on its decor. A plain colour has no direction. A woodgrain or linear print does, and the stock's grain setting should match the way the print runs on your board. Check the board itself; the direction can differ between products.
For a full comparison of the materials, see MDF vs plywood for cabinets.
Grain direction is not grain matching
Grain direction keeps a part aligned along an axis. Grain matching concerns the visual pattern between neighbouring parts, such as a row of drawer fronts. Those fronts may need to come from adjacent positions in one sheet and stay in a particular order.
Kerflio does not promise grain-pattern matching. If a design depends on a continuous figure, plan those relationships separately and inspect the actual material. One practical approach is to cut the matched set as a single panel first, then divide it.
Common grain and rotation mistakes
- Leaving rotation on for everything. The plan looks efficient, then the visible sides come out with cross grain.
- Locking every part out of habit. Hidden parts and MDF parts lose options for no reason, and the sheet count can rise, as in the 14-part example.
- Swapping length and width in the list. A 560 × 720 mm entry with grain along its length puts the grain the wrong way on a cabinet side. Keep one convention.
- Setting grain on parts but not on the stock. A part's grain only means something relative to the sheet. Set the sheet's grain to match the face.
- Keeping an old drawing. Recalculate if you change a rotation setting. An earlier drawing no longer represents the revised requirements.
Physical material still needs a check
The web planner does not see knots, face quality, defects or a veneer pattern. A geometrically valid rectangle can cross an area you do not want to use. Inspect the stock and adjust the usable region or your plan before cutting. In a completed plan, confirm the orientation of each labelled part.
Return to the sheet planner to try the 14-part example with rotation on and off, or read the full planning limitations.
Frequently asked questions
Does allowing rotation always save material?
No. It gives the planner more arrangements to try, and sometimes none of them is better. For some lists the sheet count is the same either way.
Can MDF parts rotate?
Usually yes, because plain MDF has no grain on its face. Lock them if they will be veneered with a directional face or if a pattern will show.
How do I lock grain in Kerflio?
Leave rotation off for that part. In the web planner that means leaving the rotation checkbox unticked; the app has a no-rotate setting per part.
Which way does plywood grain run on a sheet?
Often along the long side, but cross-grain panels exist. Check the face, and the label if it uses the first-dimension-parallel-to-grain convention.
Why did my plan use more sheets after I locked the grain?
Locking removes the turned arrangements that packed parts more tightly. The 14-part example on this page goes from two sheets to three for that reason.
How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.