What are the common plywood sheet sizes?
| Format | Size in mm | Area | Where it appears |
|---|---|---|---|
| 4 × 8 ft | 1,219.2 × 2,438.4 (exact conversion) | 32 ft², 2.97 m² | US and Canadian panels |
| 1,220 × 2,440 mm | 1,220 × 2,440 | 2.98 m² | Metric listing of the 4 × 8 format |
| 1,220 × 2,745 mm | 1,220 × 2,745 | 3.35 m² | About 4 × 9 ft; birch plywood ranges |
| 4 × 10 ft | 1,219.2 × 3,048 (exact conversion) | 40 ft², 3.72 m² | Longer panels from some makers |
| 1,250 × 2,500 mm | 1,250 × 2,500 | 3.125 m² | European metric ranges |
| 1,525 × 1,525 mm | 1,525 × 1,525 | 2.33 m² | Square birch, often called 5 × 5 |
The inch rows are conversion arithmetic, since one inch is exactly 25.4 mm. Riga Wood lists Riga Ply birch in 1,220 or 1,250 mm widths with lengths including 2,440, 2,500, 2,745 and 3,050 mm. WISA lists 1,220 × 2,440 and 1,250 × 2,500 mm among its formats. States Industries lists 48 × 96 in and 48 × 120 in as standard panel sizes. Koskisen lists 1,525 × 1,525 mm as a standard interior size of its thin birch plywood.
Source: Riga Wood, Riga Ply datasheet (PDF), checked 2026-11-14.
Source: WISA sizes, thicknesses and weights, checked 2026-11-14.
Source: States Industries, size options, checked 2026-11-14.
Source: Koskisen, KoskiPly Birch datasheet, checked 2026-11-14.
Source: NIST, SI units: length, checked 2026-11-14.
For sizes by region, see sheet sizes by country. For MDF formats, see MDF sheet sizes.
Is a 4×8 sheet exactly 48 by 96 inches?
Not always. APA notes that some panels are made "sized for spacing", which means slightly less than the traditional nominal 48 × 96 in. The notation is optional, and APA does not give one exact undersize, so check the sticker or measure the sheet.
A 4 × 8 sheet listed as 1,220 × 2,440 mm is also 0.8 mm wider and 1.6 mm longer than the exact conversion of 48 × 96 in. That is tiny on its own, but a layout planned to the last millimetre can lose a strip over it.
Source: APA plywood overview, checked 2026-11-14.
What are oversize sheets?
Some makers sell panels a little larger than the nominal size, so you can trim to an exact 4 × 8 or cut full-size parts after cleaning up the edges. States Industries, for example, lists TruYield panels at 49 × 97 in and 49 × 121 in, oversized by about an inch beside its 48 × 96 and 48 × 120 in standard sizes.
Source: States Industries, size options, checked 2026-11-14.
If you buy oversize stock, enter the size you measure. Do not enter the nominal 4 × 8, or the planner will give away material you paid for. If you plan to trim the sheet back to a nominal size anyway, enter the trimmed size.
Which dimension is the length, and which way does the grain run?
On many panels the first number runs parallel to the face grain. WISA states this convention for its sizes. Riga Wood lists both 1,220 × 2,440 and 2,440 × 1,220 mm formats and says its face veneers come in long grain and cross grain, so the same footprint can have the grain running either way. Check the label or the face before you plan grain-sensitive parts.
Source: WISA sizes, thicknesses and weights, checked 2026-11-14.
Source: Riga Wood, Riga Ply datasheet (PDF), checked 2026-11-14.
Kerflio treats the long side of a sheet as its length. Enter the real dimensions, then set grain direction on the stock and the parts. The grain and rotation guide shows how a grain lock can change the sheet count.
How much of a sheet is usable?
Less than the label area. Three things take material before your parts do: damaged or unsquare edges you trim off, the kerf of every cut, and offcuts too small to use. The nominal area is the upper limit, not a yield.
You need sixteen 600 × 300 mm shelves with the grain along 600 mm, cut with a 3 mm kerf from 1,220 × 2,440 mm sheets.
Across the width, four 300 mm strips need 4 × 300 + 3 × 3 = 1,209 mm. Along the length, four 600 mm parts need 4 × 600 + 3 × 3 = 2,409 mm. So 4 × 4 = 16 shelves fit on one full sheet.
Trim one long edge and one short edge (a 5 mm sliver plus a 3 mm kerf, 8 mm each). The sheet becomes 1,212 × 2,432 mm. Both 1,209 and 2,409 still fit: 16 shelves.
Trim both long edges instead and the width becomes 1,220 − 16 = 1,204 mm. Four strips need 1,209 mm, so only three fit: 12 shelves, and you need a second sheet.
The Kerflio planning engine gives the same counts for these three sheet sizes. The trim on one edge removes just under 1% of the sheet area (1,212 × 2,432 mm is 2.95 m² against 2.98 m²), but the effect on the layout depends on where your parts sit, not on the percentage.
Does a bigger sheet always give more parts?
No. Parts come in whole strips, so extra width or length only helps when it completes another strip. The table counts grain-locked parts on a full sheet in simple rows and columns with a 3 mm kerf.
| Sheet (mm) | 600 × 300 mm shelves | 720 × 560 mm cabinet sides |
|---|---|---|
| 1,219.2 × 2,438.4 (exact 4 × 8 ft) | 16 | 6 |
| 1,220 × 2,440 | 16 | 6 |
| 1,250 × 2,500 | 16 | 6 |
| 1,525 × 1,525 | 10 | 4 |
| 1,219.2 × 3,048 (exact 4 × 10 ft) | 20 | 8 |
The 1,250 × 2,500 mm sheet holds the same count as a 1,220 × 2,440 mm sheet for both parts here. Its extra material ends up in wider offcuts. The square 1,525 mm sheet fits five 300 mm strips across, but only two 600 mm parts along each strip. A planner that can mix orientations, where grain allows, may do better than this grid.
How do I check that a sheet is square?
Measure both diagonals. On a rectangle they are equal. For 1,220 × 2,440 mm each diagonal should be about 2,728 mm (√(1,220² + 2,440²) = 2,728.0 mm). If they differ, the sheet is out of square, and you will want a trim cut on at least one edge before you use it as a reference.
Manufacturer tolerances give an idea of what to expect. Riga Wood's datasheet for Riga Ply gives ±3 mm on length and width over 2,000 mm, ±2 mm from 1,000 to 2,000 mm, and a squareness tolerance of ±1 mm per metre. A sheet sold as 2,440 mm can therefore measure anywhere from 2,437 to 2,443 mm within that tolerance.
Source: Riga Wood, Riga Ply datasheet (PDF), checked 2026-11-14.
Enter the smallest length and width you measured, after any trim.
How does thickness work?
Thickness labels are nominal too. APA says the Performance Category is the nominal panel thickness used in building codes, and panels also carry a decimal thickness for labelling. Enter the thickness you measure when parts must match, especially for dados and joints. The plywood thickness chart lists nominal and metric thicknesses.
Source: APA plywood overview, checked 2026-11-14.
Common sheet size mistakes
- Planning to the nominal size. A layout that needs every millimetre of 1,220 × 2,440 mm can fail on a 1,219 mm sheet. Measure first.
- Ignoring the edge you will trim. A dinged factory edge comes off before the first part. Subtract trim and its kerf.
- Assuming grain runs along the long side. Cross-grain panels exist. Check the face.
- Buying a bigger format to save material. As the table shows, a larger sheet only helps when it completes another strip of parts.
- Mixing formats in one plan. If you have both 1,220 × 2,440 and 1,250 × 2,500 mm sheets, enter them as separate stock rows.
To work out how many sheets a project needs, follow how many sheets of plywood do I need, then check the layout in the sheet cut planner. For boards and studs, see nominal vs actual lumber sizes.
Frequently asked questions
Which size should I enter in Kerflio?
The size you measured, after trimming any damaged or unsquare edge. Use the smaller measurement if the two ends differ.
Is 1220 × 2440 mm the same as 4 × 8 feet?
Nearly. 4 × 8 ft converts to exactly 1,219.2 × 2,438.4 mm, so the metric listing is 0.8 mm wider and 1.6 mm longer. Real sheets vary by more than that, so measure.
What size is a 5 × 5 Baltic birch sheet?
It is usually listed as 1,525 × 1,525 mm, which is about 60 in square. Check the label, because square birch panels come in more than one size.
Why do some sheets measure 49 × 97 inches?
Some makers sell oversize panels with about an inch of extra material so you can trim to full size. Enter the size you measure.
Are other regions different?
Yes. Metric and inch formats both appear, and the sheet sizes by country guide covers regional formats. Confirm with your supplier.
How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.