What sizes does MDF come in?

The sheet you can buy depends on where you live and which mill made it. The table lists sizes that manufacturers publish on their own data sheets. It is not every size on the market, and a merchant may stock only a few of them.

MDF sheet sizes published by manufacturers
RegionMaker and productPublished sizes
USA and CanadaRoseburg Medite MDFWidths of 4 and 5 ft (1.22 and 1.52 m), plus 6 ft (1.83 m) from the Pembroke, Ontario mill. Lengths up to 16 or 18 ft depending on the mill. Actual length and width are one inch over the stated size.
UK and IrelandMedite Premier1220 × 2440, 1220 × 2745, 1220 × 3050, 2440 × 1830, 1525 × 2440, 1525 × 2745 and 1525 × 3050 mm
EuropeEGGER PerfectSense lacquered MDF2800 × 2070 mm
AustraliaLaminex Decorated MDF2400 × 1200 and 3600 × 1200 mm
AustraliaLaminex Structural MDF3600 × 1800 mm

Source: Roseburg Medite MDF technical data sheet, checked 2026-11-14.

Source: Medite Premier MDF technical data sheet, checked 2026-11-14.

Source: NBS Source listing for EGGER PerfectSense lacquered MDF, checked 2026-11-14.

Source: Laminex product page (White Natural, all formats), checked 2026-11-14.

For plywood and particleboard sizes side by side, country by country, see standard sheet sizes by country.

What thicknesses does MDF come in?

Most makers list a long run of metric thicknesses and leave the rest "by special request". Here is what the data sheets checked for this page say.

MDF thicknesses on manufacturer data sheets
ProductThicknesses listed
Medite Premier (Europe)3, 4, 6, 9, 12, 15, 16, 18, 19, 22, 25, 30, 32, 36, 38 and 40 mm
Roseburg Medite MDF (North America)3/16 to 1-1/8 in (El Dorado), 1/4 to 1-1/2 in (Medford), 0.47 to 1 in (Pembroke)
EGGER PerfectSense lacquered MDF18 and 19 mm
Laminex Decorated MDF16 mm in both listed sizes
Laminex Structural MDF18, 25 and 32 mm

Source: Medite Premier MDF technical data sheet, checked 2026-11-14.

Source: Roseburg Medite MDF technical data sheet, checked 2026-11-14.

Source: EGGER Availability Guide (copy hosted by a distributor), checked 2026-11-14.

Source: Laminex product page (White Natural, all formats), checked 2026-11-14.

A decorated or lacquered board carries a surface layer on its core, so measure the finished sheet with calipers if a part has to fit a groove. The plywood thickness chart covers the same problem for plywood, where the gap between label and caliper is larger.

Why is a North American 4 × 8 MDF sheet 49 × 97 inches?

Roseburg's data sheet says it plainly: actual length and width are one inch longer than the stated size. A sheet sold as 4 × 8 ft therefore arrives at about 49 × 97 in. The extra inch gives a cabinet shop room to trim the edges square and clean, and then still cut full 48 × 96 in parts if it wants to.

49 in × 25.4 = 1244.6 mm, 97 in × 25.4 = 2463.8 mm≈ 1245 × 2464 mm

That size is not a rule for every mill. Check the label or the supplier's listing, and run a tape over the sheet before you plan. Roseburg also gives a length and width tolerance of ±0.080 in (±2 mm) and a squareness tolerance of ±0.036 in per foot, so the first edge you cut may not be square to the factory edge you expected.

Source: Roseburg Medite MDF technical data sheet, checked 2026-11-14.

ARAUCO's TRUPAN Superior High Plus sheet gives a length and width tolerance of ±1/16 in and a squareness figure of 1/8 in. It shows that tolerances differ between makers, which is one more reason to measure.

Source: ARAUCO TRUPAN Superior High Plus specification sheet, checked 2026-11-14.

What does an oversize sheet change in a cut list?

Mostly it gives you room. A plan made for 48 × 96 in can lose a part to one kerf, and the extra inch can bring it back. Take two 24 in wide panels ripped across the width of the sheet with a 1/8 in kerf between them.

Worked example: two 24 in rips from a 4 ft MDF sheet

Parts plus one kerf: 24 + 24 + 0.125 = 48.125 in.

On a true 48 in sheet the second rip comes out 1/8 in narrow (48 − 24 − 0.125 = 23.875 in).

On a 49 in sheet both parts fit, with 49 − 48.125 = 0.875 in left for trimming the factory edge.

The metric version works the same way. Two 600 mm parts with a 3 mm kerf need 600 + 600 + 3 = 1203 mm. A 1220 mm sheet leaves 1220 − 1203 = 17 mm, which is enough to take a clean edge off one side.

If you do trim a factory edge first, enter the sheet at its trimmed size. Kerflio treats the stock size you type as fully usable. It does not know you plan to remove a strip, so subtract the trim and the kerf of that cut yourself. Saw kerf explains why every cut takes material.

Which size should I type into the planner?

  1. Measure the length and width of the sheet at both ends. Use the smaller reading.
  2. Decide whether you will trim an edge. If so, subtract the trim width plus one kerf from that dimension.
  3. Enter that usable size as the stock in the sheet cut planner.
  4. Enter your measured kerf. If you have not measured it, measure your saw kerf with a test cut.
  5. Run the plan and check the leftover strip along each edge.
Worked example: usable size after trimming one long edge

Sheet measured: 2463 × 1244 mm.

Trim 10 mm off one long edge with a 3 mm kerf: 1244 − 10 − 3 = 1231 mm.

Enter 2463 × 1231 mm as the stock size.

Plain MDF has no grain, so you can allow parts to rotate. That gives the layout search more arrangements to try. A lacquered, foiled or melamine board with a wood-grain print is different: treat it like veneer and keep the rotation off for parts where the pattern direction shows. Grain and rotation explains the setting.

Is 18 mm MDF really 18 mm?

Much closer than plywood usually is. Medite Premier lists a thickness tolerance of ±0.15 mm for every thickness band, and Roseburg lists ±0.005 in (±0.125 mm) for the panel average from the specified thickness. ARAUCO gives ±0.005 in for TRUPAN Superior High Plus.

Source: Medite Premier MDF technical data sheet, checked 2026-11-14.

Source: Roseburg Medite MDF technical data sheet, checked 2026-11-14.

Source: ARAUCO TRUPAN Superior High Plus specification sheet, checked 2026-11-14.

That consistency is one reason MDF suits grooves, dados and painted cabinet doors. It still swells when it takes on water: Medite Premier's sheet lists a maximum 24 hour thickness swell of 9% for boards over 12 mm up to 19 mm under the EN 317 test. Store sheets flat and dry, and let them settle in the room before you cut. Medite asks for two to three days of conditioning to the final environment.

Source: Medite Premier MDF technical data sheet, checked 2026-11-14.

Do MDF sheets move after cutting?

A little, with humidity. Medite Premier lists length and width movement of 0.30% for boards over 12 mm up to 19 mm, measured by the EN 318 test method. It is a laboratory figure, so read it as a sign that MDF moves a small amount, not as an allowance to add to every part. It matters when you cut parts in a damp garage and assemble them in a dry house, or the other way round. Cut, fit and assemble in similar conditions when you can.

Source: Medite Premier MDF technical data sheet, checked 2026-11-14.

Common mistakes with MDF sheet sizes

  • Planning a 49 × 97 in sheet as 48 × 96 in. Harmless, but you may buy a sheet you did not need.
  • Planning a 48 × 96 in sheet as 49 × 97 in. The plan fails on the last rip, so measure first.
  • Mixing thicknesses in one stock group. 16 mm and 18 mm boards look alike on a stack. Group stock by material and thickness, as described in how to make a cut list.
  • Forgetting the trim cut. A factory edge with a chipped corner costs a strip and a kerf.
  • Rotating printed boards. Wood-grain decor boards need the same no-rotate care as veneered plywood.

Comparing MDF with plywood for a cabinet job? MDF vs plywood for cabinets puts the data sheet figures side by side.

Frequently asked questions

Is a 4 × 8 sheet of MDF exactly 4 by 8 feet?

Not always. Roseburg states that its actual length and width are one inch longer than the stated size, so a 4 × 8 ft panel is about 49 × 97 in. Other mills may differ, so measure the sheet.

What is the standard MDF sheet size in the UK?

Medite lists 1220 × 2440 mm first among its Premier sizes, with longer and wider sheets such as 1220 × 3050 mm and 1525 × 3050 mm also listed. Your merchant may stock only some of them.

What MDF sizes are sold in Australia?

Laminex lists decorated MDF at 2400 × 1200 mm and 3600 × 1200 mm, and structural MDF at 3600 × 1800 mm. Thicknesses vary by product.

Can I rotate MDF parts in a cut plan?

Plain raw MDF has no grain, so rotation is usually fine. Turn rotation off for printed, foiled or veneered boards where the pattern direction shows.

Why does my plan say a part does not fit when the area is enough?

Area ignores the shape of the leftovers and the kerf. Strips beside large parts are often too narrow to use. The layout, not the area total, decides the sheet count.

How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.