What is saw kerf, in planning terms?

Kerf is the slot a blade leaves behind. For a cut list it is a length: if the kerf is 3 mm, each cut turns 3 mm of your stock into dust. The parts you keep never include it.

Three numbers decide what fits on a piece of stock: the part sizes, the number of cuts between them, and the kerf. The first two come from your drawing and your layout. The third comes from your saw and blade, and it is worth measuring rather than guessing. The kerf measuring guide shows a test cut, and the saw kerf chart collects typical values by tool. This page sticks to the arithmetic, using 3 mm and 1/8 in as example kerfs.

The 3 mm value in the website planners is an example. It is not a recommendation for every blade. Enter the value you measured for the blade, material and saw you will actually use.

Two pieces from one board

Take a straight 1,000 mm board. You need two 400 mm pieces, and the cut removes 3 mm each time.

400 + 3 + 400 + 3 + 194= 1,000 mm

After the first cut you have one 400 mm piece and 597 mm left. The second cut separates another 400 mm piece, removes 3 mm, and leaves 194 mm. The finished pieces total 800 mm; 6 mm becomes kerf and 194 mm remains as an offcut.

You can reproduce this in the linear cut planner by entering a 1,000 mm board, two 400 mm parts and a 3 mm kerf.

Why does the number of cuts matter more than the number of parts?

Because a part that ends at the end of the stock needs no cut on that side. Two 400 mm parts can meet opposite ends of an 803 mm board with a single 3 mm cut between them. There is no remainder to remove after the second part, so only one kerf is spent. That is why "part count × kerf" is not a universal formula.

Count the cuts instead. On a single board where the last part uses the end of the board, the number of cuts is the number of parts minus one. If the last part does not reach the end, you need one more cut to free it, and that cut leaves an offcut.

Cuts and kerf for parts along one board (3 mm kerf)
SituationCutsKerf spent
2 parts, last part ends at the board end13 mm
2 parts, offcut left over26 mm
5 parts, last part ends at the board end412 mm
5 parts, offcut left over515 mm

In a sheet layout, a cut can divide a rectangle that is later split again, so the count follows the order of the cuts. Read guillotine cuts explained for how sheet layouts break down.

Worked example: ripping a sheet into strips

You want 300 mm wide strips from a sheet that is 1,220 mm wide, with a 3 mm kerf. How many full strips do you get, and what is left?

Worked example: 300 mm strips from 1,220 mm

Four strips with three cuts between them: 4 × 300 + 3 × 3 = 1,209 mm.

1,220 − 1,209 = 11 mm extra, which stays on the last strip. That strip measures 311 mm.

To bring it to 300 mm you make a fourth cut: 1,220 − 4 × 300 − 4 × 3 = 8 mm offcut.

Result: four 300 mm strips, 12 mm of kerf and an 8 mm sliver.

A fifth strip would need 5 × 300 + 4 × 3 = 1,512 mm, far more than the sheet. The sheet width also assumes you use the factory edge as is. If you trim a damaged edge first, that trim and its kerf come off before any strip; see the section on trim below.

Why does a 2440 mm sheet not give four 610 mm strips?

Because 4 × 610 = 2,440 mm exactly, which leaves nothing for the blade. Three cuts separate four pieces, and each one removes material.

Worked example: four strips from 2,440 mm, 3 mm kerf

Kerf for three cuts: 3 × 3 = 9 mm.

Cut three strips at 610 mm: 2,440 − 3 × 610 − 9 = 601 mm. The fourth strip is 601 mm, 9 mm short.

If you want four equal strips instead: (2,440 − 9) ÷ 4 = 607.75 mm each.

The same happens in inches. A 96 in length cut into four 24 in pieces with a 1/8 in kerf spends 3 × 1/8 = 3/8 in on three cuts, so the last piece is 96 − 72 − 3/8 = 23 5/8 in.

Keep in mind that a sheet sold as 4 × 8 ft may not be a full 96 in long. The plywood sheet sizes guide explains nominal and real sheet dimensions. If your design really needs 610 mm or 24 in parts, plan them from longer stock or change the part size.

How does kerf add up over many cuts?

One kerf looks small. Seven of them in a row are not. Narrow parts suffer most because the number of cuts grows while each part stays small.

Worked example: 150 mm strips from a 1,220 mm sheet

Eight strips need 8 × 150 = 1,200 mm of parts plus 7 cuts × 3 mm = 21 mm of kerf.

1,200 + 21 = 1,221 mm, which is 1 mm more than the sheet.

Seven full strips use 7 × 150 + 7 × 3 = 1,071 mm, leaving 1,220 − 1,071 = 149 mm for the eighth strip.

On paper the parts total less than the sheet, so the list looks like it fits. With kerf it misses by a millimetre. The inch version is just as tight: eight 6 in strips from 48 in with a 1/8 in kerf leave the last strip at 48 − 7 × 6 − 7 × 1/8 = 5 1/8 in.

Total kerf for repeated cuts
CutsAt 3 mmAt 1/8 in
39 mm3/8 in
721 mm7/8 in
1133 mm1 3/8 in
1545 mm1 7/8 in

A planner that counts each cut catches this before you are standing at the saw with a short part.

Worked example: crosscutting a board into parts

You have a 2,400 mm board and need four 595 mm parts, with a 3 mm kerf.

Worked example: four 595 mm parts from 2,400 mm

Parts: 4 × 595 = 2,380 mm. Three cuts between them: 9 mm. Total 2,389 mm.

2,400 − 2,389 = 11 mm extra, which stays on the last part (606 mm).

A fourth cut trims it to 595 mm: 2,400 − 2,380 − 4 × 3 = 8 mm offcut.

Now try 550 mm parts. Four of them with four cuts use 4 × 550 + 4 × 3 = 2,212 mm and leave a 188 mm offcut. A fifth 550 mm part would need 2,750 mm. Whether a 188 mm piece is worth keeping depends on your work; what offcuts to keep covers that choice.

Kerf and trim are different

Kerf is removed by the blade. Trim is stock you set aside to remove a rough, damaged or unsquare edge. A 1,000 mm board with 10 mm trimmed from each end has 980 mm of usable length before planning the remaining cuts.

A trim cut also costs a kerf. Removing a 5 mm sliver with a 3 mm blade takes 8 mm off that edge. Enter usable stock dimensions in the web planner, after trim. Do not add a guessed waste percentage to the kerf field; they describe different things, and a padded kerf can push a part that would have fitted onto the unplaced list.

Common kerf mistakes

  • Adding parts without cuts. Summing part sizes and comparing with the stock ignores every cut. The 150 mm strip example above fails by 1 mm this way.
  • Multiplying parts by kerf. It overcounts when the last part ends at the stock edge, and can make a good layout look impossible.
  • Marking every part at once from one end. If you mark 400, 800 and 1,200 mm on a board and cut on each line, the blade eats into the parts. Mark the next part after each cut, or allow for the kerf in the marks.
  • Using a label value for a different tool. A track saw, table saw and handsaw rarely cut the same width. Use a value for the tool doing the cut.
  • Forgetting to recalculate. Changing kerf can turn a close fit into an unplaced part. Recalculate after changing it and use the new plan.

How does Kerflio handle kerf?

You enter one kerf for the job. The planner leaves that gap wherever a cut separates two pieces in its layout, follows the actual partition of each board or sheet, and does not multiply every part by a fixed number. A separate check confirms that parts do not overlap and stay inside the stock before a plan is shown. The search is a heuristic, so it does not promise the fewest sheets; read how Kerflio plans cuts for the limits.

Try the examples above in the free sheet cut planner or linear cut planner. Both run in your browser and take up to 12 pieces.

Frequently asked questions

Is kerf the same as waste?

Kerf is one kind of waste: the material the blade turns into dust. Trim and offcuts are separate, and an offcut may still be useful stock.

Should I add kerf to each part size?

No. Keep parts at their finished size and enter kerf separately. The planner adds kerf once per cut, which is not always once per part.

What kerf should I enter if I have not measured?

Use the blade maker's stated cut width as a starting point, then measure a test cut. The measure-your-saw-kerf guide shows how.

Does kerf matter for a single cut?

Only if the two pieces must both be full size. One cut through a 1,000 mm board leaves 997 mm of pieces in total with a 3 mm kerf.

Why is my last strip always short?

Because the strip sizes add up to the stock size with nothing left for the cuts. Count the cuts, multiply by your kerf, and take that from the last strip or reduce each strip.

How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.