Which offcuts are worth keeping?

An offcut is worth keeping when three things are true: it is big enough to give you a part you really make, it is the same material and thickness as that part, and it is flat and undamaged enough that you would trust it in a finished piece. If any one of those fails, the piece is scrap, however nice the wood looks.

Most offcut piles grow because the decision is made piece by piece, at the end of a long day, with the thought that something might come in handy. A written size rule replaces that guess. You decide once, at a quiet moment, what your smallest useful part is, and the rule does the sorting at the saw.

This page covers the keep-or-discard decision, labelling and storage, and how to put kept pieces back into a plan. Keeping the record itself (fields, consuming a piece once, backups) is covered in how to keep a useful offcut inventory.

How do I set a minimum offcut size?

Start from the parts you cut most often, not from a number someone else uses. Go through your last few cut lists and pick out the small parts that come up again and again: drawer sides, cleats, small shelves, jig bases, spacers. Your minimum size is the smallest of those parts plus a trim allowance.

The trim allowance covers one clean-up cut on each edge you will need to true up. Each trim cut costs one kerf plus the thin sliver you remove, so measure your own kerf first (how to measure your saw kerf) and decide how wide a sliver you want to take off a rough or chipped edge.

minimum offcut side = smallest common part side + trim allowanceset once, write it on the rack
Worked example: setting the rule for 18 mm plywood

Common small parts from recent jobs: cleat 300 × 60 mm, drawer side 450 × 120 mm, small shelf 300 × 250 mm.

Smallest length: 300 mm. Smallest width: 60 mm.

Trim allowance chosen for this shop: 10 mm on each dimension (one kerf plus a sliver).

Rule: keep 18 mm plywood offcuts that are at least 300 + 10 = 310 mm long and at least 60 + 10 = 70 mm wide.

The numbers in that example are one shop's choices. If you never make cleats, your smallest width might be 120 mm, and the rule would keep far fewer narrow strips. If you have room for only one small rack, raise the rule until the pile fits.

Does the rule change by material?

Yes, because materials fail in different ways once they are cut small. The size rule tells you whether a piece is big enough. The material check tells you whether it is still good enough. Use the table as a list of things to look at, then decide for your own stock.

What to check before keeping an offcut, by material
MaterialCheck before keepingOften worth keeping
PlywoodFace veneer intact, no delamination at the edges, flat when laid on a benchStrips and rectangles above your size rule, especially the face grade you use for visible parts
MDF and other fibreboardCorners and edges not crushed, no swelling from damp, flatPieces for jigs, templates and painted parts above your size rule
Melamine or veneer-faced panelsFaces not chipped near where your parts would come from, matching colour or speciesPieces large enough for a part with a clean face and edge
Solid boardsStraight, no splits running in from the ends, no large knots in the usable lengthLengths above your shortest common board part plus a trim allowance
Thin panels used for backs and drawer bottomsFlat, no torn cornersPieces at least as big as one drawer bottom or back you make often

Keep each material and thickness separate in your head and on the rack. A piece of 12 mm plywood is no help when the part list asks for 18 mm, even if the face size fits perfectly. The MDF versus plywood comparison covers how the two materials differ in use.

Worked example: which offcuts from a real plan pass the rule?

Here are the leftovers from two sheet plans on this site, tested against the 310 × 70 mm rule for 18 mm plywood from the example above. The first three come from the cutting order example, the rest from the cutting diagram example.

Offcuts tested against a 310 × 70 mm minimum
Offcut (mm)Long side ≥ 310?Short side ≥ 70?Decision
2440 × 94YesYesKeep: cleat stock
560 × 271YesYesKeep
560 × 303YesYesKeep
400 × 31YesNoDiscard
380 × 151YesYesKeep
760 × 51YesNoDiscard
1677 × 434YesYesKeep, and store it with the part-sheets
Worked example: what the long strip is worth

Strip: 2440 × 94 mm. Part: cleat 300 × 60 mm. Kerf: 3 mm (an assumed value for this example).

Width: 94 ≥ 60 + 10, so one rip trims it to cleat width.

Length: each cleat uses 300 mm plus one 3 mm kerf between neighbours. 8 cleats need 8 × 300 + 7 × 3 = 2421 mm, which fits in 2440 mm. 9 would need 2727 mm, which does not.

So the strip is worth 8 cleats.

Doing that sum for a doubtful piece once or twice teaches you what your rule really means. Soon you can see at a glance that a 31 mm strip will never be a part in your shop.

How should I label offcuts?

Put the label on the piece itself, where you will see it when it sits on the rack. Pencil on an edge or a strip of masking tape works. Write the material, the thickness, the measured size and a short ID. Measure after the last cut, not from the cutting diagram, because a planned leftover can end up smaller than drawn.

A simple label format
Part of the labelExampleWhy
IDBP-12Matches the record, so you can find the piece the plan asks for
Material and thicknessBirch ply 18Parts only come from matching stock
Measured size560 × 303Long side first, written in the unit you plan in
Grain markarrow along 560Shows which way the face grain runs for parts that cannot be turned

Use one unit throughout. If you plan in millimetres, label in millimetres. Mixing inches and millimetres on the same rack is a common way to cut a part from the wrong piece. See fractions, inches and millimetres.

How should I store kept offcuts?

Store by material and thickness first, then by size. Within a thickness, a few size bands are enough: long strips, mid-size rectangles, and large part-sheets. Put the bands where you can see every label without unstacking the pile, because a piece you cannot find is the same as a piece you do not have.

  • Keep panels flat or standing on edge with support along their length so they stay flat.
  • Keep solid board offcuts sorted by length so the shortest ones do not hide behind long ones.
  • Give each band a fixed space. When the space is full, the size rule goes up or the smallest pieces go.
  • Keep a scrap bin next to the saw for everything below the rule, so it never reaches the rack.

Review the rack when you start a project. Anything that has sat untouched for a long stretch and fails your current rule can go. The right review interval depends on how often you build, so pick one you will actually keep to.

How do I feed kept offcuts into the next plan?

Enter the offcuts as stock before you add new full sheets or boards. That way the planner tries the material you already have first, and you buy only what is left over. Use the measured size from the label, the same material and thickness as the parts, and the grain direction if any part needs it.

  1. Pull the IDs that match the job's material and thickness.
  2. Enter each one as a stock item with its measured size.
  3. Add full sheets or board lengths after them.
  4. Run the plan and read the placed and unplaced counts. Every part must be placed before you cut.
  5. After cutting, mark the used offcuts as consumed and label any new leftover that passes your rule.

In the free sheet planner and linear planner you type offcuts in as stock for the current calculation. The Kerflio Android app's full access adds an offcut library of up to 5,000 offcuts, so kept pieces stay listed between projects. The record-keeping side, including not counting a piece twice, is in the offcut inventory guide.

What mistakes make an offcut pile useless?

  • No rule at all, so every piece is kept and the useful ones get buried.
  • A rule copied from someone else's shop instead of set from your own parts.
  • Labels taken from the cutting diagram rather than measured after cutting.
  • Mixed thicknesses on one shelf, so a 15 mm piece gets picked for an 18 mm part.
  • Kept offcuts never entered as stock, so new sheets get cut while the rack fills up.
  • Grain direction not marked on pieces meant for visible parts. See grain and rotation.

Fixing the first two removes most of the others. Once the rule is written down and the rack has fixed space, the pile can only hold pieces you have already decided are useful. For ways to leave fewer small leftovers in the first place, read how to reduce plywood waste.

Frequently asked questions

Is there a standard minimum offcut size?

No single size suits every shop. Set it from the smallest part you make often, plus a trim allowance for one clean-up cut, and raise it if your storage is full.

Should I keep offcuts smaller than my rule for small projects?

Only if you have a specific use for them now. Otherwise put them in the scrap bin, because small pieces kept "just in case" bury the useful ones.

Do I measure offcuts before or after cutting?

After. A planned leftover on the diagram can come out smaller because of an extra trim or a damaged corner, so the label should carry the measured size.

Can Kerflio store my offcuts?

The free web planners let you enter offcuts as stock for one calculation. The Android app with full access keeps an offcut library of up to 5,000 offcuts between projects.

Should solid wood offcuts follow the same rule as plywood?

Use the same method with a length rule: your shortest common board part plus a trim allowance. Check for splits at the ends before you keep a piece.

How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.