How do I convert inches to millimetres?
Multiply by 25.4. The inch has been defined as exactly 25.4 mm since 1959, so this is not an approximation and there is nothing to round in the factor itself.
Source: NIST, SI units: length, checked 2026-11-14.
To go the other way, divide millimetres by 25.4. A 600 mm part is 600 ÷ 25.4 = 23.622 in. The inches to mm chart lists the common values so you can look them up instead.
A mixed fraction, worked through
To convert 15 3/16 inches, first turn the fraction into a decimal: 3 ÷ 16 = 0.1875. Then multiply 15.1875 by 25.4. The result is 385.7625 mm.
A displayed rounded value is not a new measurement. Kerflio's planning engine uses millimetres rounded to 0.001 mm. That precision is a software representation; it does not claim a tool or measuring device can achieve the same tolerance.
Common fractions
| Inches | Decimal inches | Millimetres |
|---|---|---|
| 1/64 | 0.015625 | 0.396875 |
| 1/32 | 0.03125 | 0.79375 |
| 1/16 | 0.0625 | 1.5875 |
| 1/8 | 0.125 | 3.175 |
| 1/4 | 0.25 | 6.35 |
| 1/2 | 0.5 | 12.7 |
| 5/8 | 0.625 | 15.875 |
| 3/4 | 0.75 | 19.05 |
The full set of sixteenths, thirty-seconds and sixty-fourths is in the fraction to decimal chart.
How do I enter fractions in Kerflio?
Choose inches as the unit, then type the measurement the way you would write it. The planner reads:
- whole numbers and decimals:
24,23.5 - simple fractions:
3/4 - mixed fractions with a space or a dash:
23 1/2or23-1/2(the dash means "and a half", never subtraction) - an optional unit mark at the end:
23 1/2 inor23 1/2"
A few entries are rejected on purpose. The fraction part of a mixed number must be smaller than one, so 23 5/4 is refused instead of being guessed at. Denominators run from 1 to 1,024. Typing mm into an inch field is refused too, so a stray unit cannot silently change a size. Use the unit selector first.
In millimetres, enter decimals. The web demo accepts decimals in millimetres and decimals or mixed fractions in inches. It converts the current dimensions when you switch units.
How should I round when converting?
Round once, at the end, to a step your tape or rule can show. Rounding every part on the way in can drift a whole list.
600 ÷ 25.4 = 23.622 in.
23.622 × 16 = 377.95, which rounds to 378 sixteenths.
378 ÷ 16 = 23.625 in = 23 5/8 in, which is 600.075 mm. The rounded value is 0.075 mm long.
450 mm = 17.7165 in. To the nearest 1/16 in that is 17 11/16 in = 449.2625 mm, about 0.74 mm short.
Six of these parts placed end to end: 6 × 0.7375 = 4.425 mm short in total.
If the six parts must fill an opening, that gap shows. Keep the original 450 mm in the cut list and round only the number you mark.
Which direction to round depends on the part. A part that must fit inside an opening can safely round down a hair; a part you will trim to fit later can round up.
Worked example: an inch cut list in millimetres
Say a bookcase drawing gives these finished sizes, and your sheet is sold and measured in millimetres. Convert each size with × 25.4 and keep three decimals, which is the precision the planner stores.
| Part | Inches | Exact mm | Rounded to whole mm |
|---|---|---|---|
| Side | 35 1/4 | 895.35 | 895 |
| Top | 23 15/16 | 608.0125 (608.012 stored) | 608 |
| Shelf | 22 7/16 | 569.9125 (569.913 stored) | 570 |
| Back rail | 22 7/16 | 569.9125 (569.913 stored) | 570 |
| Kick | 3 1/2 | 88.9 | 89 |
There is no need to convert by hand at all: set the planner to inches and type the fractions. If you do convert, the whole-millimetre column is fine for marking a single part. It is less fine for a run of parts. Three shelves end to end are 1,709.74 mm exact but 1,710 mm rounded, a 0.26 mm difference here, which grows with every part and can go either way.
Write the unit in the column heading of your list, not in each cell, and never mix two units in one column unless each row says which unit it uses.
Adding fractions in a cut list
Fractions add like any numbers once they share a denominator. Kerf counts too.
Three 11 3/8 in shelves with a 1/8 in kerf between each.
3 × 11 3/8 = 34 1/8 in. Two cuts × 1/8 in = 1/4 in.
34 1/8 + 1/4 = 34 3/8 in of board, which is 873.125 mm. If a third cut frees the last shelf from an offcut, add another 1/8 in.
For step-by-step fraction arithmetic with a tape measure, see adding fractions for woodworking. The saw kerf guide explains when a cut needs a kerf and when it does not.
Mixed-unit lists: what goes wrong?
Most mixed-unit trouble comes from treating a nominal size in one system as an exact size in the other.
A drawing gives a 22 1/2 in inside width and 3/4 in sides. Outside width: 22 1/2 + 2 × 3/4 = 24 in = 609.6 mm.
You build it from sheet that measures 18 mm. Outside width: 571.5 + 2 × 18 = 607.5 mm.
The carcass is 2.1 mm narrower than the drawing. Any part sized from the drawing's outside width, such as a top or a face frame, is now 2.1 mm too wide.
The fix is to convert the drawing once, then replace nominal values with the sizes you measure. The plywood thickness chart shows why a "3/4" sheet and an 18 mm sheet are not always the same thing.
Sheet sizes behave the same way. A 4 × 8 ft sheet is 1,219.2 × 2,438.4 mm; a metric 1,220 × 2,440 mm sheet is 0.8 mm wider and 1.6 mm longer. A layout planned on one can miss by a strip on the other.
Does switching units change my project?
When changing the unit shown in a planner, the physical dimensions should stay the same. A 1,000 mm stock length becomes about 39.3701 inches; it should not become 1,000 inches. Review the displayed dimensions after a conversion, especially when moving a cut list between programs.
Kerflio stores every size in millimetres to 0.001 mm and converts for display, so switching units back and forth does not wear the numbers down.
Before importing a spreadsheet
Keep a separate quantity column, label the units and check a few rows against the original drawing. Decimal commas, thousands separators and quotation marks can change how a file is read. A rejected row should be corrected rather than silently omitted.
The Kerflio app for Android imports a CSV file and shows a preview before it replaces your rows. Its CSV has a unit column that takes mm or in per row, so a list can mix units as long as each row says which one it uses. It can also export a CSV cut list and a JSON backup. The cut list CSV format page lists the columns.
Common unit mistakes
- Typing millimetres into an inch field. 600 entered as inches is over 15 m. Check the unit selector before the first row.
- Rounding each part before planning. Small errors add up along a strip, as in the six-part example.
- Converting 3/4 in to 18 mm. 3/4 in is 19.05 mm. If your sheet measures 18 mm, enter 18; do not change the inch value to match.
- Reading 1-1/2 as subtraction. In a cut list the dash joins the whole number and the fraction.
- Mixing decimal commas and points. 1,220 can mean one thousand two hundred and twenty or one point two two. Pick one style for the whole file.
Frequently asked questions
Is 1 inch exactly 25.4 mm?
Yes. The inch has been defined as exactly 25.4 mm since 1959, so conversions only round when you choose to.
Can I type 23 1/2 into Kerflio?
Yes, with the unit set to inches. It also reads 23-1/2, 23.5 and an optional in or inch mark at the end.
What precision does Kerflio keep?
It stores sizes in millimetres rounded to 0.001 mm. That is a software precision, not a claim about what a saw or tape can achieve.
Should I plan in inches or millimetres?
Use the unit your tape and drawing use. Kerflio converts either way, so the choice is about reading the plan at the saw without mistakes.
How do I round 600 mm to a tape-measure fraction?
600 mm is 23.622 in, which rounds to 23 5/8 in at 1/16 in steps. Keep 600 mm in the list and round only the mark.
How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.