How do I add fractions with different denominators?
You can only add fractions that have the same bottom number. In woodworking the denominators are almost always 2, 4, 8, 16, 32 or 64, so the easy common denominator is the largest one in the problem. Convert each fraction by multiplying top and bottom by the same number until the bottom matches.
| Fraction | In 16ths | In 32nds | In 64ths | Decimal (in) |
|---|---|---|---|---|
| 1/2 | 8/16 | 16/32 | 32/64 | 0.5 |
| 1/4 | 4/16 | 8/32 | 16/64 | 0.25 |
| 3/4 | 12/16 | 24/32 | 48/64 | 0.75 |
| 1/8 | 2/16 | 4/32 | 8/64 | 0.125 |
| 3/8 | 6/16 | 12/32 | 24/64 | 0.375 |
| 5/8 | 10/16 | 20/32 | 40/64 | 0.625 |
| 7/8 | 14/16 | 28/32 | 56/64 | 0.875 |
Largest denominator is 16.
5/8 = 10/16, 3/16 stays 3/16, 7/8 = 14/16
10 + 3 + 14 = 27, so the sum is 27/16
27/16 = 1 11/16 (16 goes into 27 once, with 11 left over)
When a sum of the tops is larger than the denominator, divide to get whole inches and a remainder, as in the last line. Then reduce the remainder if you can. 12/16 reduces to 3/4 by dividing top and bottom by 4.
A cut list example: three parts from one board with 1/8 in kerf
You need three parts from an 8 ft (96 in) board: 23 5/8 in, 31 3/16 in and 18 7/8 in. Your measured kerf is 1/8 in. Cut them one after another from one end. Each part needs one cut to separate it from the rest of the board, so three parts use three kerfs and leave an offcut. If the board's factory end is not square you will also trim it, which is a separate allowance discussed below.
23 5/8 = 378/16 (23 × 16 = 368, plus 5/8 = 10/16)
31 3/16 = 499/16 (31 × 16 = 496, plus 3/16)
18 7/8 = 302/16 (18 × 16 = 288, plus 7/8 = 14/16)
378 + 499 + 302 = 1179/16 = 73 11/16 in
Three cuts × 1/8 in = 3/8 in = 6/16
1179/16 + 6/16 = 1185/16 = 74 1/16 in used
96 in = 1536/16, and 1536 − 1185 = 351/16
Offcut: 351/16 = 21 15/16 in
Check the answer in decimals: 23.625 + 31.1875 + 18.875 + 0.375 = 74.0625 in, and 96 − 74.0625 = 21.9375 in, which is 21 15/16. Both methods agree. Whether that offcut is worth keeping is covered in what offcuts to keep.
How do I subtract mixed fractions?
Subtraction is where most shop arithmetic goes wrong, because you sometimes have to borrow an inch. Convert both numbers to the same denominator first. If the fraction you are subtracting is larger, take one whole inch from the first number and add it as 16/16.
10 1/8 = 10 2/16
2/16 is smaller than 7/16, so borrow: 10 2/16 = 9 18/16
9 18/16 − 3 7/16 = 6 11/16
Check: 10.125 − 3.4375 = 6.6875, and 0.6875 = 11/16
A quicker route for long lists is to turn every size into whole sixteenths, as in the board example above, and work only with whole numbers. 10 1/8 is 162 sixteenths and 3 7/16 is 55. 162 − 55 = 107 sixteenths, and 107 ÷ 16 = 6 remainder 11, so 6 11/16 in again.
When should I convert to decimals instead?
Decimals are easier on a calculator or in a spreadsheet, and you avoid the borrowing step. The cost is the conversion back to a fraction for marking. Use decimals for the arithmetic and fractions for the tape:
- Convert every fraction to a decimal: 7/16 = 0.4375. The fraction to decimal chart lists every 64th.
- Add or subtract with all the decimal places.
- Convert the final answer back: multiply the decimal part by 16 (or 32), round, and put it over 16 (or 32).
Five equal drawer fronts with four 1/8 in gaps fill a 33 1/2 in opening. What height is each front?
Gaps: 4 × 0.125 = 0.5 in. Space left for fronts: 33.5 − 0.5 = 33 in.
33 ÷ 5 = 6.6 in. Decimal part 0.6 × 16 = 9.6, which rounds to 10/16 = 5/8.
Rounded height: 6 5/8 in. Five of them come to 33 1/8 in, which is 1/8 in more than the 33 in available.
That last line is the reason to check a rounded result against the total. Each front was rounded up by 0.025 in, and five of those add up to 0.125 in. Here you could make the gaps slightly smaller or round down to 6 9/16 in and accept a slightly larger gap.
How do I add feet and inches?
Add the fractions first, then the inches, then the feet, carrying as you go: every 16/16 becomes an inch and every 12 in becomes a foot. Or turn the whole thing into inches, add, and turn it back.
Fractions: 5/8 = 10/16, and 10/16 + 11/16 = 21/16 = 1 5/16. Write 5/16, carry 1 in.
Inches: 7 + 9 + 1 carried = 17 in = 1 ft 5 in. Write 5 in, carry 1 ft.
Feet: 3 + 2 + 1 carried = 6 ft.
Result: 6 ft 5 5/16 in. Check in inches: 43.625 + 33.6875 = 77.3125 in, and 77.3125 − 72 = 5.3125 in = 5 5/16 in.
Two parts need two cuts with a 1/8 in kerf, 1/4 in in all.
96 − 77.3125 − 0.25 = 18.4375 in, which is 18 7/16 in.
Which way should I round a fraction?
Rounding to the nearest mark is fine for most parts, but some parts have a safe direction:
| Number | Round | Why |
|---|---|---|
| Part that fits between two fixed parts (shelf, divider, panel in a groove) | Down | A part that is slightly short still fits; one that is long does not |
| Part you will trim to fit later (face frame, edge strip) | Up | You can remove material but not add it |
| Usable stock length or width | Down | Planning with stock you do not have causes an unplaced part |
| Kerf | Up | A kerf entered too small makes the plan look tighter than the saw allows |
| Total of many identical parts | Round the total, not each part | Avoids errors adding up |
For parts that must fit between others, also watch the stack. A cabinet with two 3/4 in sides and an outside width of 24 in has an inside width of 24 − 3/4 − 3/4 = 22 1/2 in. If the sides are really 23/32 in plywood, the inside is 24 − 46/32 = 22 9/16 in. Measure the sheet before you add.
Common mistakes when adding shop fractions
- Adding the denominators: 1/4 + 1/4 is 2/4 = 1/2, never 2/8.
- Forgetting the kerf, or counting it once per part when the last part ends at the board end. See how many pieces from a board for when the final kerf is needed.
- Borrowing a whole inch as 10/16 instead of 16/16, a slip that comes from decimal habits.
- Rounding every line of a long list and then adding the rounded numbers.
- Mixing a measured 23/32 in sheet with a nominal 3/4 in in the same calculation.
Can a planner do this arithmetic for me?
Yes. In the linear cut planner you can type 23 5/8, 31 3/16 and 18 7/8 with a 96 in board and a 1/8 in kerf, and it places the parts and reports what is left. It keeps the exact values while planning, so you only round when you mark. Do the hand method once so you can tell when a result looks wrong. A quick check is to add the parts in decimals on a phone calculator and compare the total with the planner's used length.
Frequently asked questions
What is the easiest common denominator for shop fractions?
Use the largest denominator in the problem, usually 16 or 32. Every half, quarter and eighth converts to 16ths without remainders.
How do I add 5/8 and 3/16?
5/8 is 10/16, so 10/16 + 3/16 = 13/16 in.
How much kerf do three cuts take with a 1/8 inch blade?
Three cuts at 1/8 in each remove 3/8 in of board.
Should I round shelf lengths up or down?
Down, to the nearest mark below, when the shelf must fit between two fixed sides. A slightly short shelf still fits.
Is it better to work in decimals?
Decimals avoid borrowing and are easier in a spreadsheet. Convert back to 16ths or 32nds only when you mark the part.
How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.