What is the formula?

pieces = floor((L + k) ÷ (p + k))L = usable board length, p = piece length, k = kerf

The formula comes from what n pieces really use. Cutting n pieces in a row needs n pieces and a kerf between each pair: n × p + (n − 1) × k. That total has to fit in the board. Rearranged, n × (p + k) ≤ L + k, so n is (L + k) ÷ (p + k) rounded down. The extra kerf added to L is there because the last piece can end at the end of the board without a cut after it.

If the last piece must be separated from an offcut, as in most real cuts, that cut lands in the offcut and does not change the count. The leftover is then:

leftover = L − n × p − (n − 1) × kincludes the slot of the last cut if you make one

The saw kerf page shows the same idea with a two-piece example.

Worked examples in feet and inches

Worked example: 14 1/2 in pieces from an 8 ft board, 1/8 in kerf

L = 96 in, p = 14.5 in, k = 0.125 in

(96 + 0.125) ÷ (14.5 + 0.125) = 96.125 ÷ 14.625 = 6.573

Round down: 6 pieces

Leftover: 96 − 6 × 14.5 − 5 × 0.125 = 8 3/8 in

Worked example: Eight pieces of 11 7/8 in from the same board

L = 96, p = 11.875, k = 0.125

96.125 ÷ 12 = 8.0104, round down to 8

Leftover: 96 − 8 × 11.875 − 7 × 0.125 = 1/8 in

This fits with 1/8 in to spare. With 12 in pieces the answer drops to 7, because 8 × 12 + 7 × 0.125 = 96.875 in is more than 96.

Pieces from a 96 in (8 ft) board with a 1/8 in kerf and no end trim
Piece lengthPiecesLeftover
6 in154 1/4 in
8 in116 3/4 in
10 in95 in
11 7/8 in81/8 in
12 in711 1/4 in
14 1/2 in68 3/8 in
16 in515 1/2 in
18 in55 1/2 in
20 in415 5/8 in
24 in323 3/4 in
30 in35 3/4 in
36 in223 7/8 in
48 in148 in

Worked examples in millimetres

Worked example: 450 mm pieces from a 2400 mm board, 3 mm kerf

(2400 + 3) ÷ (450 + 3) = 2403 ÷ 453 = 5.305

Round down: 5 pieces

Leftover: 2400 − 5 × 450 − 4 × 3 = 138 mm

Worked example: Four 600 mm pieces from 2400 mm?

Four pieces and three kerfs: 4 × 600 + 3 × 3 = 2409 mm

That is 9 mm more than 2400 mm, so only 3 fit. The formula agrees: 2403 ÷ 603 = 3.985.

Either shorten each piece to 597 mm or less, or start from a longer board.

Pieces from a 2400 mm board with a 3 mm kerf and no end trim
Piece lengthPiecesLeftover
150 mm15108 mm
200 mm11170 mm
250 mm9126 mm
300 mm7282 mm
350 mm6285 mm
400 mm5388 mm
450 mm5138 mm
500 mm4391 mm
600 mm3594 mm
700 mm3294 mm
800 mm2797 mm
1000 mm2397 mm
1200 mm11,200 mm

How does end trim change the count?

Boards often arrive with a split, checked or out-of-square end. Cutting it off removes length you cannot use, so plan with the board length after trimming. Trimming one end also costs one kerf, because the trim cut is a cut. The simplest way to handle both is to measure the board after you square the ends and use that number for L.

Worked example: Trimming 1/2 in from each end of an 8 ft board

Usable length: 96 − 0.5 − 0.5 = 95 in (measured after the trim cuts)

14 1/2 in pieces: (95 + 0.125) ÷ 14.625 = 6.504, still 6 pieces, leftover 7 3/8 in

11 7/8 in pieces: (95 + 0.125) ÷ 12 = 7.927, now only 7 pieces

Worked example: Trimming 10 mm from each end of a 2400 mm board

Usable length: 2380 mm. 450 mm pieces: 2383 ÷ 453 = 5.260, still 5, leftover 118 mm.

The 11 7/8 in case shows why trim matters: a plan with 1/8 in to spare loses a whole piece once you square the ends. When a count is that close, measure the board after trimming before you cut the first part.

How many boards do I need for a given number of pieces?

Work out how many pieces fit in one board, then divide the number of pieces you need by that count and round up.

boards = ceiling(pieces needed ÷ pieces per board)round up, because a part board is still a board to buy
Worked example: 20 pieces of 14 1/2 in from 8 ft boards, 1/8 in kerf

Pieces per board: 6 (from the example above).

20 ÷ 6 = 3.33, round up to 4 boards.

Three full boards give 18 pieces. The fourth board gives the last 2 and leaves 96 − 2 × 14.5 − 0.125 = 66 7/8 in, long enough for other parts on the list.

Worked example: 32 pieces of 450 mm from 2400 mm boards, 3 mm kerf

Pieces per board: 5. 32 ÷ 5 = 6.4, round up to 7 boards.

The seventh board gives 2 pieces and leaves 2400 − 2 × 450 − 3 = 1497 mm.

A large leftover on the last board is a sign to check whether another part on your list can go there, or whether a shorter stock length would do for that last board.

What if the pieces have different lengths?

The formula works for one piece length. With mixed lengths the order and grouping decide how many boards you need, and the obvious method is not always the best. A common hand method is to take the longest part first and put each part in the first board where it fits.

Worked example: Six parts from 2400 mm boards, 3 mm kerf

Parts: 1200, 1000, 750, 700, 600, 400 mm (total 4650 mm).

Longest first, first board that fits: board 1: 1200 + 1000; board 2: 750 + 700 + 600; board 3: 400. That needs 3 boards.

A better grouping: board 1: 1200 + 750 + 400 = 2356 mm with kerfs, leftover 44 mm; board 2: 1000 + 700 + 600 = 2306 mm, leftover 94 mm. That needs 2 boards.

The difference is a whole board. Searching groupings by hand gets slow beyond a handful of parts, which is what a planner is for. The bench boards cut list example shows another case where a simple total misleads.

When should I use the linear planner instead?

  • When parts have more than one length.
  • When you have boards of different lengths, including offcuts you want to use first. See offcut inventory.
  • When the count is close to the limit and you want to see the leftover for each board.
  • When the list is long enough that a missed part would be costly.

The free linear cut planner takes up to 12 pieces, counts kerf between parts and reports placed parts, unplaced parts and the leftover on each board. It uses a heuristic search and does not promise the best possible grouping, so for a plan that matters, look at the layout and check the counts. For one length from one board, the formula on this page is quicker. For sheets rather than boards, see sheet versus linear cutting.

Common mistakes when counting pieces

  • Dividing the board by the piece length and ignoring kerf. 96 ÷ 12 = 8, but only 7 fit with a 1/8 in kerf.
  • Counting one kerf per piece when the last piece ends at the board end. The formula already handles that.
  • Using the length on the label rather than the measured, trimmed length.
  • Rounding the result up. 5.97 pieces is 5 pieces.
  • Using the published kerf when your saw cuts wider. See saw kerf chart and measure.

Frequently asked questions

How many 12 inch pieces can I cut from an 8 foot board?

7 with a 1/8 in kerf. Eight would need 96 7/8 in.

How many 600 mm pieces from a 2.4 m board?

3 with a 3 mm kerf. Four pieces need 2409 mm.

Why add one kerf to the board length?

Because n pieces need only n − 1 kerfs between them. Adding one kerf to L makes the division come out right.

Does trimming the ends change the count?

It can. Plan with the length you measure after squaring the ends.

Does this formula work for mixed lengths?

No. With mixed lengths the grouping matters; use the linear cut planner or try groupings by hand.

How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.