What lengths does US lumber come in?

The USDA Forest Products Laboratory Wood Handbook describes softwood lumber as manufactured in length multiples of 1 ft under the grading rules, with even 2 ft multiples common for most construction lumber. Retail yards often stock dimension lumber in lengths of 8 to 18 ft in 2 ft steps. Hardwood lumber is different: standard hardwood lengths run from 4 to 16 ft in 1 ft increments, and hardwood is usually manufactured to random widths.

Common US softwood lengths with exact metric conversions
LengthInchesMillimetresMetres
8 ft96 in2,438.42.438
10 ft120 in3,048.03.048
12 ft144 in3,657.63.658
14 ft168 in4,267.24.267
16 ft192 in4,876.84.877

Source: USDA Forest Products Laboratory, Wood Handbook (FPL-GTR-282), chapter 6, Lumber Manufacture and Retail Yard Inventory, checked 2026-11-14.

Length is the one dimension sold at its stated size. The Wood Handbook notes that lumber length is recorded in actual dimensions, while width and thickness are recorded as nominal sizes. For actual widths and thicknesses, see nominal versus actual lumber sizes.

Why are studs 92 5/8 in and 104 5/8 in?

Precut studs are trimmed to a length that suits a standard wall rather than a whole number of feet. US retailers list 2×4 precut studs at 92 5/8 in and 104 5/8 in. Menards describes the 92 5/8 in stud as precision end trimmed for a typical wall with an 8 ft finished ceiling, and its 104 5/8 in stud as cut to build a 9 ft wall with a single bottom plate and a double top plate.

Precut stud lengths
StudFeet and inchesMillimetresWith three 1 1/2 in plates
92 5/8 in7 ft 8 5/8 in2,352.78 ft 1 1/8 in
104 5/8 in8 ft 8 5/8 in2,657.59 ft 1 1/8 in

Adding a single bottom plate and a double top plate, three 1 1/2 in thicknesses, to a 92 5/8 in stud gives 8 ft 1 1/8 in. For a woodworking cut list the point is simpler: if your parts fit in about 7 ft 8 in, a precut stud can be a convenient source of softwood, and its ends are already trimmed square at the mill.

Source: Menards, 2 × 4 × 92 5/8 in pre-cut stud, checked 2026-11-14.

Source: Menards, 2 × 4 × 104 5/8 in pre-cut stud, checked 2026-11-14.

What lengths are sold in metric countries?

Metric framing timber is commonly listed in 0.3 m steps from 2.4 m. Australian merchant Bunnings lists 90 × 45 mm MGP10 framing pine in lengths including 2.4, 3.0, 3.6, 4.2 and 6.0 m. UK merchant Travis Perkins lists 38 × 89 mm CLS studwork timber in 2.4, 3.0 and 4.8 m lengths. Availability varies by branch and product, so check the listing for the section you want.

Metric lengths in inches and feet (nearest 1/16 in)
LengthmmInchesFeet and inches
2.4 m2,40094.497 ft 10 1/2 in
2.7 m2,700106.308 ft 10 5/16 in
3.0 m3,000118.119 ft 10 1/8 in
3.6 m3,600141.7311 ft 9 3/4 in
4.2 m4,200165.3513 ft 9 3/8 in
4.8 m4,800188.9815 ft 9 in
5.4 m5,400212.6017 ft 8 5/8 in
6.0 m6,000236.2219 ft 8 1/4 in

2.4 m is 1.512 in shorter than 8 ft, and 4.8 m is 3.024 in shorter than 16 ft. If you follow an imperial plan with metric timber, recheck any plan that uses the full 8 ft.

Source: Bunnings Australia, 90 × 45 mm MGP10 pine 2.4 m, checked 2026-11-14.

Source: Bunnings Australia, 90 × 45 mm MGP10 pine 6.0 m, checked 2026-11-14.

Source: Travis Perkins, 38 × 89 mm × 4.8 m CLS, checked 2026-11-14.

Source: Travis Perkins, 38 × 89 mm × 3 m CLS, checked 2026-11-14.

How do I choose a stock length for a linear cut list?

Start from the longest part and the number of copies. Count how many fit in each stock length with the formula from how many pieces from a board, then compare the total length you would buy.

Worked example: Six parts 30 in long, 1/8 in kerf

Each stock length, counted with floor((L + 0.125) ÷ 30.125):

30 in parts per stock length, 1/8 in kerf
StockPartsLeftover
8 ft35 3/4 in
10 ft329 3/4 in
12 ft423 5/8 in
16 ft611 3/8 in

Two 8 ft boards give six parts and buy 192 in. A 12 ft board gives four and needs an 8 ft board for the other two, 240 in in all. A 10 ft board is the trap: it gives three parts and leaves 29 3/4 in, 1/4 in short of a fourth. Two 8 ft boards buy less length here than the 12 ft plus 8 ft option. A single 16 ft board also gives all six parts, with 11 3/8 in left, and buys the same 192 in as two 8 ft boards. Between those two, the choice comes down to price per foot, straightness and whether a 16 ft board fits in your vehicle.

Worked example: Metric: 600 mm parts from 2.4 m

Four parts need 4 × 600 + 3 × 3 = 2409 mm with a 3 mm kerf, so a 2.4 m length gives 3.

A 3.0 m length gives floor(3003 ÷ 603) = 4 parts with 591 mm left. A 4.8 m length gives 7 with 582 mm left.

Shortening the parts to 597 mm would let four come out of 2.4 m, with 3 mm left, if the design allows.

Some rules that help:

  • Check the near misses. A leftover just short of one more part means a small change in part length or kerf, or a longer board, gains a whole part.
  • Allow for end trim. Most boards need a square end; measure after trimming. See the trim examples on how many pieces from a board.
  • Think about handling. A 16 ft board can be harder to transport and to cut accurately than two 8 ft boards. Ask the yard to crosscut if your vehicle is short, and give them the lengths from your plan.
  • Use offcuts first. Short parts often fit in offcuts from earlier jobs. See offcut inventory.

Is a board always exactly its stated length?

Do not assume so. Lengths are stated in actual dimensions, but ends can be split, out of square or damaged in handling, and you may need to trim them. Measure each board, square one end, and plan with what is left. A board you plan as 96 in that turns out to have a split 3 in into one end is 93 in of usable stock. In the examples above, that is enough to lose a part.

Thickness and width also differ from the name. A 2×4 is not 2 × 4 in, and 4/4 hardwood is 13/16 in after surfacing on two sides. Plan parts with the actual size; the board foot calculation page explains how hardwood is priced.

Common mistakes when buying lengths

  • Buying 8 ft boards for parts that add up to exactly 96 in. The kerfs alone push the total over.
  • Treating 2.4 m as 8 ft. It is 1.512 in shorter.
  • Choosing the longest available board to save money without checking whether the extra length produces another part.
  • Planning hardwood parts around a width you assume the yard has. Hardwood is usually made to random widths, so plan with the boards you see on the rack.

Can I plan with several stock lengths at once?

Yes. In the linear cut planner you can enter boards of different lengths and let it place parts across them. It counts the kerf, shows which parts were placed and which were not, and reports the leftover on each board. Try two 8 ft boards against one 12 ft and one 8 ft to see the comparison above for yourself.

Frequently asked questions

What lengths does 2×4 lumber come in?

US retailers commonly stock even-foot lengths such as 8, 10, 12, 14 and 16 ft, plus precut studs of 92 5/8 in and 104 5/8 in.

Why is a precut stud 92 5/8 inches?

Menards describes it as trimmed to frame a typical wall with an 8 ft finished ceiling. The stud plus three 1 1/2 in plates is 8 ft 1 1/8 in.

Is 2.4 m the same as 8 feet?

No. 2.4 m is 7 ft 10 1/2 in, about 1.51 in shorter than 8 ft.

What lengths does hardwood come in?

The Wood Handbook gives standard hardwood lengths from 4 to 16 ft in 1 ft steps. Widths are usually random.

Should I buy one long board or two short ones?

Count the parts each option yields with the kerf included, then compare total length and price. Two shorter boards often waste less.

How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.