What is an offcut inventory for?
An offcut inventory is a list of the leftover pieces you have decided to keep, written so that a planner or a person can use them in the next job. Its job is to stop two things: buying a new sheet when a usable piece is already on the rack, and planning a part from a piece that no longer exists.
Deciding which pieces to keep is a separate question, covered in what offcuts to keep. This page is about the record: what goes in it, when an entry is created and removed, and how to keep the list and the rack in agreement.
Keep planned and actual stock separate
A rectangle left on a cutting diagram is a planned offcut. It becomes actual stock only after the cuts are complete and the piece has been measured. A changed cut, damaged corner or extra trim can make the real piece smaller.
Label the physical piece and use the same label in your record. A location such as "rack B, lower shelf" makes the entry useful when planning the next project.
| Planned offcut | Actual offcut | |
|---|---|---|
| Where it comes from | The cutting diagram | The saw, after the last cut |
| Size | As drawn | As measured |
| Belongs in the inventory? | No | Yes, if it passes your keep rule |
| Can be used in another plan? | No, it does not exist yet | Yes |
Record what makes a piece compatible
Write down material, thickness, length and width, and the grain or pattern direction if it matters. A 12 mm panel cannot replace an 18 mm panel just because the face dimensions fit. Keep irregular or damaged pieces clearly marked; a rectangular planner cannot model every usable shape.
Birch plywood · 18 mm thick · 510 × 275 mm · grain along 510 mm · label BP-07 · rack B.
| Field | Example | Why it is there |
|---|---|---|
| Label | BP-07 | Links the record to the physical piece |
| Material | Birch plywood | Parts only come from matching material |
| Thickness | 18 mm | Parts only come from matching thickness |
| Length × width | 510 × 275 mm | Measured after cutting |
| Grain | Along 510 mm | Grain-locked parts can only use the piece one way |
| Location | Rack B | So you can find it when the plan asks for it |
| Notes | Chipped corner at one end | Flags a defect the planner cannot see |
If a piece has a damaged corner, record the largest clean rectangle you would actually use, not the outside size. The planner treats every stock item as a full rectangle, so a piece entered at its outside size can get a part placed over the damage.
Consume a piece once
When a real offcut is used, remove or reduce that inventory record. If the new job creates another useful remainder, add that measured piece with its own identity. Re-running a planner is not the same as cutting more stock.
Record before: BP-07, birch plywood 18 mm, 510 × 275 mm.
Job: one part at 400 × 275 mm, cut across the 510 mm length, with a 3 mm kerf (an assumed value for this example).
Left after the cut: 510 − 400 − 3 = 107 mm, so a planned remainder of 107 × 275 mm.
After cutting, measure the remainder. If it passes your keep rule, record it as a new piece, for example BP-13, at its measured size. Remove BP-07 from the inventory.
The order matters. Remove BP-07 when the cut is made, not when the plan is made. If you plan three versions of the job, the inventory should still show BP-07 once until you actually cut it. A record that drops or adds pieces each time you press "plan" soon shows material you do not have.
How do I keep the list and the rack in agreement?
Most inventory errors come from a piece that changed on the rack but not in the list, or the other way round. A few habits keep them together:
- Update the record at the saw, right after the cut, not at the end of the week.
- Use one label per piece, and never reuse a label for a different piece.
- When you trim a piece, record the new measured size under a new label or update the old one, but not both.
- When you throw a piece out, delete its record at the same time.
- Every so often, walk the rack with the list and check each label against its record.
If you find a piece with no record, measure it and add it. If you find a record with no piece, delete it. Do not keep a record "in case it turns up", because a planner will happily plan parts from it.
Worked example: an inventory before and after one job
Here is a small inventory of 18 mm birch plywood, a job that uses two of its pieces, and what the list looks like afterwards. Kerf 3 mm (an assumed value for this example). The keep rule is 310 × 70 mm, set as described in what offcuts to keep.
| Label | Size (mm) | Location |
|---|---|---|
| BP-07 | 510 × 275 | Rack B |
| BP-12 | 560 × 303 | Rack B |
| BP-14 | 2440 × 94 | Strip rack |
One small shelf 300 × 250 mm from BP-12. Crosscut at 300: 560 − 300 − 3 = 257 mm left, a piece 257 × 303. Rip the shelf to 250: 303 − 250 − 3 = 50 mm, a strip that goes in the scrap bin.
Four cleat blanks 300 mm long from BP-14. 4 × (300 + 3) = 1212 mm used, leaving 2440 − 1212 = 1228 mm, a piece 1228 × 94.
Now test the leftovers against the rule. The 257 × 303 piece has a long side of 303 mm, under 310, so it does not pass and goes in the scrap bin even though it looks like a decent square. The 1228 × 94 strip passes and gets a new label after it is measured.
| Label | Size (mm) | Change |
|---|---|---|
| BP-07 | 510 × 275 | Unchanged |
| BP-12 | Removed: used, leftover below the rule | |
| BP-14 | Removed: used | |
| BP-15 | 1228 × 94 (measured) | New: remainder of BP-14 |
The list went from three pieces to two, and every entry matches a piece on the rack. Had BP-14 been reduced in place to 1228 × 94 instead of given a new label, that would also work, as long as only one of the two methods is used.
Choose what is worth keeping
The useful minimum depends on the work you do and the space you have. A narrow strip can be useful for one workshop and clutter in another. Record the pieces you are likely to use, and review the shelf as well as the list.
A written rule set from your own common parts makes this quick. What offcuts to keep shows how to set one, with checks by material and worked examples.
How do I use the inventory in the next plan?
Filter the inventory by the job's material and thickness. Enter the matching pieces as stock before any new sheets or boards, so the planner tries them first. Check the placed and unplaced counts, then note which offcut labels the plan used.
In the free sheet planner and linear planner, you type offcuts in as stock for the current calculation. The web demo shows remainders for the current calculation and does not maintain an inventory.
The Kerflio app keeps a persistent offcut library as part of full access, with room for up to 5,000 offcuts. It is an Android app with an optional one-time purchase, no subscription and no account. The app also imports and exports CSV, described in the CSV format guide.
Back up the record
A regular backup keeps the record portable. Check the restored dimensions, units and quantities before relying on an imported inventory.
The units check matters most. A list exported in millimetres and read back as inches, or the other way round, can look normal at a glance and be wrong for every piece. Spot-check two or three records against the labels on the rack after any restore. See fractions, inches and millimetres.
Frequently asked questions
When should I add an offcut to my inventory?
After the cut is made and the piece is measured. A leftover on a cutting diagram is only planned until then.
What if an offcut has a damaged corner?
Record the largest clean rectangle you would use, and add a note. A rectangular planner treats each stock item as a full rectangle.
Does the free web planner keep my offcuts?
No. It shows remainders for the current calculation only. The Android app with full access keeps an offcut library of up to 5,000 offcuts.
How do I avoid counting the same offcut twice?
Give each piece one label, remove its record when it is cut, and add any new remainder under a new label after measuring it.
How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.