What is the exact conversion?
One inch is exactly 25.4 mm and one foot is exactly 304.8 mm. These values are definitions, so the conversion of a length in inches to millimetres is always exact; only the rounding you choose afterwards introduces error.
Source: NIST SP 811, Appendix B.8 (inch = 0.0254 m, foot = 0.3048 m, both exact), checked 2026-11-14.
For a mixed measurement such as 5 ft 7 3/8 in, turn everything into inches first, then multiply once.
5 ft × 12 = 60 in
60 + 7 + 3/8 = 67.375 in
67.375 × 25.4 = 1,711.325 mm
Inches 1 to 12 in millimetres
These are exact, which is why they have only one decimal place. Add a fraction from the fraction to decimal chart for in-between sizes.
| Inches | Millimetres | Centimetres |
|---|---|---|
| 1 in | 25.4 | 2.54 |
| 2 in | 50.8 | 5.08 |
| 3 in | 76.2 | 7.62 |
| 4 in | 101.6 | 10.16 |
| 5 in | 127.0 | 12.70 |
| 6 in | 152.4 | 15.24 |
| 7 in | 177.8 | 17.78 |
| 8 in | 203.2 | 20.32 |
| 9 in | 228.6 | 22.86 |
| 10 in | 254.0 | 25.40 |
| 11 in | 279.4 | 27.94 |
| 12 in | 304.8 | 30.48 |
Board and sheet lengths from 2 ft to 16 ft
Boards are commonly sold in even-foot lengths, and a full sheet in North America is 4 × 8 ft. This table converts every whole foot from 2 to 16 ft. See standard lumber lengths for which lengths are actually stocked.
| Feet | Inches | Millimetres | Metres |
|---|---|---|---|
| 2 ft | 24 in | 609.6 | 0.6096 |
| 3 ft | 36 in | 914.4 | 0.9144 |
| 4 ft | 48 in | 1,219.2 | 1.2192 |
| 5 ft | 60 in | 1,524.0 | 1.5240 |
| 6 ft | 72 in | 1,828.8 | 1.8288 |
| 7 ft | 84 in | 2,133.6 | 2.1336 |
| 8 ft | 96 in | 2,438.4 | 2.4384 |
| 9 ft | 108 in | 2,743.2 | 2.7432 |
| 10 ft | 120 in | 3,048.0 | 3.0480 |
| 11 ft | 132 in | 3,352.8 | 3.3528 |
| 12 ft | 144 in | 3,657.6 | 3.6576 |
| 13 ft | 156 in | 3,962.4 | 3.9624 |
| 14 ft | 168 in | 4,267.2 | 4.2672 |
| 15 ft | 180 in | 4,572.0 | 4.5720 |
| 16 ft | 192 in | 4,876.8 | 4.8768 |
An 8 ft board is 2,438.4 mm, a little under 2.44 m. That gap is the reason a metric 2440 mm sheet and an imperial 8 ft sheet are close but not the same, which the next section shows.
Common metric sizes to the nearest 1/16 inch
The table converts metric thicknesses and panel sizes into inches, rounds each to the nearest 1/16 in, and shows how far that rounded mark is from the true size. A positive difference means the inch mark is longer or thicker than the metric size.
| mm | Decimal inches | Nearest 1/16 in | That mark in mm | Difference (mm) |
|---|---|---|---|---|
| 3 | 0.1181 | 1/8 in | 3.175 | +0.175 |
| 6 | 0.2362 | 1/4 in | 6.350 | +0.350 |
| 9 | 0.3543 | 3/8 in | 9.525 | +0.525 |
| 12 | 0.4724 | 1/2 in | 12.700 | +0.700 |
| 15 | 0.5906 | 9/16 in | 14.288 | −0.713 |
| 18 | 0.7087 | 11/16 in | 17.463 | −0.538 |
| 19 | 0.7480 | 3/4 in | 19.050 | +0.050 |
| 22 | 0.8661 | 7/8 in | 22.225 | +0.225 |
| 25 | 0.9843 | 1 in | 25.400 | +0.400 |
| 32 | 1.2598 | 1 1/4 in | 31.750 | −0.250 |
| 50 | 1.9685 | 1 15/16 in | 49.213 | −0.788 |
| 100 | 3.9370 | 3 15/16 in | 100.012 | +0.012 |
| 300 | 11.8110 | 11 13/16 in | 300.037 | +0.037 |
| 450 | 17.7165 | 1 ft 5 11/16 in | 449.263 | −0.738 |
| 600 | 23.6220 | 1 ft 11 5/8 in | 600.075 | +0.075 |
| 900 | 35.4331 | 2 ft 11 7/16 in | 900.113 | +0.112 |
| 1,200 | 47.2441 | 3 ft 11 1/4 in | 1,200.150 | +0.150 |
| 1,220 | 48.0315 | 4 ft 1/16 in | 1,220.788 | +0.787 |
| 1,250 | 49.2126 | 4 ft 1 3/16 in | 1,249.363 | −0.638 |
| 2,400 | 94.4882 | 7 ft 10 1/2 in | 2,400.300 | +0.300 |
| 2,440 | 96.0630 | 8 ft 1/16 in | 2,439.987 | −0.013 |
| 2,500 | 98.4252 | 8 ft 2 7/16 in | 2,500.313 | +0.313 |
| 3,000 | 118.1102 | 9 ft 10 1/8 in | 3,000.375 | +0.375 |
| 3,050 | 120.0787 | 10 ft 1/16 in | 3,049.587 | −0.413 |
Two rows deserve attention. 18 mm is 0.7087 in and rounds to 11/16 in, about half a millimetre thin. 2440 mm is 96.0630 in, which is 8 ft plus 0.0630 in, close to 1/16 in over 8 ft. For sheet sizes by region, see sheet sizes by country.
How do I convert millimetres to feet, inches and sixteenths?
Divide by 25.4 to get decimal inches. Take out whole feet by dividing by 12. Keep the whole inches. Turn the decimal that is left into 16ths with the rounding rule round(decimal × 16) ÷ 16.
1830 ÷ 25.4 = 72.0472 in
72.0472 ÷ 12 = 6.0039, so 6 ft, which uses 72 in
72.0472 − 72 = 0.0472 in, which is 0 in plus 0.0472 in
0.0472 × 16 = 0.76, which rounds to 1/16
Result: 6 ft 1/16 in
If the rounded sixteenths come out at 16/16, add one inch and write zero sixteenths. If the inches reach 12, add one foot. A calculator that shows feet and inches does the same steps, so it is worth knowing them when you need to check a result that looks odd.
Which way should I convert a cut list?
Convert in one direction only and keep the original numbers. If the drawing is metric and your tape is in inches, convert each finished part size once from the drawing, and do not convert a converted number back. Each round trip adds rounding error.
When stock and parts are in different systems, put everything into the unit you will measure with. A metric sheet with an inch parts list is common in some markets: a 2440 × 1220 mm sheet is 96.063 × 48.031 in. Using 96 × 48 in instead throws away about 0.063 in in one direction and 0.031 in in the other. That may not matter, but it is a choice you should make on purpose.
The reverse case is just as common. If the drawing is in millimetres and you will cut with an inch tape, convert the parts and leave the sheet as you measured it. A part of 597 mm becomes 23.5039 in, which you would mark at 23 1/2 in, 0.100 mm away from the drawing. Write both numbers on the cut list so anyone checking the part can see where it came from.
For mixed fractional arithmetic before converting, see adding fractions for woodworking.
How do I convert a whole cut list?
Convert each finished size once, keep the exact value, and round only in the last column you will read from the tape. Rounding to whole millimetres is fine for most metric tapes. The example below converts a small shelf unit drawn in inches.
| Part | Qty | Inches | Exact mm | Rounded mm |
|---|---|---|---|---|
| Side | 2 | 35 1/4 × 11 1/4 | 895.350 × 285.750 | 895 × 286 |
| Shelf | 3 | 28 1/2 × 11 | 723.900 × 279.400 | 724 × 279 |
| Top | 1 | 30 × 12 | 762.000 × 304.800 | 762 × 305 |
| Back | 1 | 29 1/4 × 35 1/4 | 742.950 × 895.350 | 743 × 895 |
Check the rounded parts against each other where they meet. Here the shelves rounded to 724 mm, which is 0.1 mm longer than the exact 723.9 mm. If the shelves sit between the sides in dadoes, that small change is harmless. If they must match a fixed opening exactly, cut them from the exact value or round down. The rule is the same as for fractions, described in adding fractions for woodworking.
Common mistakes when converting lengths
- Using 25 instead of 25.4. Over 8 ft that shortcut loses 38.4 mm.
- Converting feet as if they were inches. 8 ft is 2,438.4 mm, not 203.2 mm.
- Writing 2.4 m as 8 ft. 2.4 m is 7 ft 10 1/2 in, which is 1.512 in short of 8 ft.
- Assuming nominal thickness matches the mm label. Measure plywood and MDF with calipers before setting a dado or groove.
- Dropping a leading zero in a decimal. 0.625 in written as .625 is easy to misread on a dusty sheet of paper.
Do I need to convert before using Kerflio?
No. The web planners and the Android app accept millimetres, decimal inches and mixed fractions. Pick the unit you measured in and enter the numbers as you have them. If you change the unit selector, the dimensions already entered are converted, so a 1,000 mm board becomes about 39.3701 in and stays the same physical length. Try it in the linear cut planner or the sheet cut planner.
Frequently asked questions
How many mm is 1 inch?
Exactly 25.4 mm. The value is defined, not measured.
How many mm is 8 feet?
8 ft is 96 in, which is 2,438.4 mm or 2.4384 m.
Is 2440 mm the same as 8 feet?
No. 2440 mm is 96.063 in, about 1.6 mm longer than 8 ft (2,438.4 mm).
What is 18 mm in inches?
18 mm is 0.7087 in. The nearest 1/16 is 11/16 in and the nearest 1/32 is 23/32 in.
How do I convert mm to feet and inches?
Divide by 25.4 for inches, take out whole feet by dividing by 12, then round the leftover decimal inch to the nearest 1/16.
How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.