How do I use this chart?

Find the fraction in the left column. The middle column is the same length in decimal inches and the right column is millimetres to three decimal places. Fractions are shown in lowest terms, so 32/64 appears as 1/2 and 8/64 as 1/8. For a whole number plus a fraction, such as 15 3/8 in, convert the fraction from the chart and add the whole inches: 15 + 0.375 = 15.375 in, and 15.375 × 25.4 = 390.525 mm.

Every decimal in the inch column is exact. Any 64th of an inch ends after at most six decimal places, because 64 is a power of two. The millimetre column is rounded to 0.001 mm, which is far finer than any tape, rule or saw fence can hold. Use the extra digits for arithmetic and round only when you write the final size on the part.

Source: NIST SP 811, Appendix B.8 (inch = 0.0254 m, foot = 0.3048 m, both exact), checked 2026-11-14.

Full 1/64 inch chart

Fractions of an inch in 64ths, decimal inches and millimetres (1 in = 25.4 mm)
Fraction (in)Decimal (in)Millimetres
1/640.0156250.397
1/320.031250.794
3/640.0468751.191
1/160.06251.588
5/640.0781251.984
3/320.093752.381
7/640.1093752.778
1/80.1253.175
9/640.1406253.572
5/320.156253.969
11/640.1718754.366
3/160.18754.762
13/640.2031255.159
7/320.218755.556
15/640.2343755.953
1/40.256.350
17/640.2656256.747
9/320.281257.144
19/640.2968757.541
5/160.31257.938
21/640.3281258.334
11/320.343758.731
23/640.3593759.128
3/80.3759.525
25/640.3906259.922
13/320.4062510.319
27/640.42187510.716
7/160.437511.112
29/640.45312511.509
15/320.4687511.906
31/640.48437512.303
1/20.512.700
33/640.51562513.097
17/320.5312513.494
35/640.54687513.891
9/160.562514.288
37/640.57812514.684
19/320.5937515.081
39/640.60937515.478
5/80.62515.875
41/640.64062516.272
21/320.6562516.669
43/640.67187517.066
11/160.687517.463
45/640.70312517.859
23/320.7187518.256
47/640.73437518.653
3/40.7519.050
49/640.76562519.447
25/320.7812519.844
51/640.79687520.241
13/160.812520.638
53/640.82812521.034
27/320.8437521.431
55/640.85937521.828
7/80.87522.225
57/640.89062522.622
29/320.9062523.019
59/640.92187523.416
15/160.937523.813
61/640.95312524.209
31/320.9687524.606
63/640.98437525.003
1125.400

How do I convert a fraction that is not on the chart?

Use the same two steps for any fraction. Divide numerator by denominator for decimal inches. Multiply by 25.4 for millimetres. The method works for odd denominators such as 1/3 or 5/12 that come from dividing a length into equal parts, even though those decimals never end.

Worked example: 23/64 in to decimal and millimetres

23 ÷ 64 = 0.359375 in

0.359375 × 25.4 = 9.128125 mm, which rounds to 9.128 mm

Worked example: 1/3 of 10 in

10 ÷ 3 = 3.3333 in (the 3 repeats)

3.3333 in × 25.4 = 84.667 mm

On a tape that reads in 16ths, 3.3333 × 16 = 53.33, which rounds to 53/16, so mark 3 5/16 in.

To go the other way, from millimetres to a fraction, divide by 25.4 for decimal inches, then use the rounding method in the next section.

How do I round a decimal to the nearest 1/16 or 1/32 inch?

Multiply the decimal part by the denominator you want, round to the nearest whole number, and put that number over the denominator. Reduce the fraction if you can.

nearest 1/16 = round(decimal × 16) ÷ 16same idea for 1/32: round(decimal × 32) ÷ 32
Worked example: 0.4 in on a tape

0.4 × 16 = 6.4, which rounds to 6, so the nearest 1/16 is 6/16 = 3/8 in.

0.4 × 32 = 12.8, which rounds to 13, so the nearest 1/32 is 13/32 in.

Error at 1/16: −0.0250 in (−0.635 mm). Error at 1/32: +0.00625 in (+0.159 mm).

Common decimals rounded to the nearest 1/16 and 1/32 inch, with the error in mm (rounded value minus true value)
Decimal (in)Nearest 1/16Error (mm)Nearest 1/32Error (mm)
0.11/8+0.6353/32−0.159
0.23/16−0.3183/16−0.318
0.35/16+0.3185/16+0.318
0.43/8−0.63513/32+0.159
0.65/8+0.63519/32−0.159
0.711/16−0.31711/16−0.317
0.813/16+0.31713/16+0.317
0.97/8−0.63529/32+0.159

Rounding to the nearest step can never be off by more than half a step. The table below gives that worst case for each tape resolution.

Largest possible rounding error for each resolution
Rounding toWorst case (in)Worst case, decimalWorst case (mm)
1/8 in1/16 in0.06251.588
1/16 in1/32 in0.031250.794
1/32 in1/64 in0.0156250.397
1/64 in1/128 in0.0078130.198

When does rounding to 1/16 or 1/32 matter?

For a single cut, rounding to the nearest 1/16 in is usually fine. A pencil line is wide, and the worst-case error of 0.794 mm is close to what you can see on a tape. Rounding starts to matter in three situations, and in all of them the fix is to plan with the exact value and round once at the end.

  • Errors that add up. If six shelves sit side by side in a cabinet and each one is rounded down by 1/32 in, the row comes out 3/16 in short. Round the total, then divide, instead of rounding each piece.
  • Parts that must fit between other parts. A shelf that drops between two sides, a drawer front in an opening or a panel in a groove has a fixed space to fill. Here the direction of rounding matters more than the step size. See adding fractions for woodworking for which way to round.
  • Metric sheet goods in an inch drawing. 18 mm plywood is 0.7087 in. The nearest 1/16 is 11/16 in, which is 0.538 mm thin, while the nearest 1/32 is 23/32 in, only 0.256 mm off. Measure the actual sheet, because labelled and actual thickness can differ. The plywood thickness chart covers this.

Keep the unrounded number in your planner and round only on the shop drawing. Kerflio's planning engine stores sizes in millimetres rounded to 0.001 mm, so a 15 3/16 in part keeps its full value of 385.763 mm while it is being placed.

Which conversions are worth knowing by heart?

A few anchors make it easy to spot a wrong number before it reaches the saw. One sixteenth is 1.5875 mm, so any number of sixteenths converts with one multiplication: 11/16 in is 11 × 1.5875 = 17.4625 mm. One thirty-second is 0.79375 mm, a little under a millimetre.

Useful anchors for mental checks
FractionExact mmRough check
1/320.794just under 1 mm
1/161.588about 1.6 mm
1/83.175a little over 3 mm
1/46.350about 6.4 mm
5/815.875about 16 mm
3/419.050just over 19 mm

If a calculator says 3/4 in is 1.9 mm or 190 mm, you have slipped a decimal point. The rough column is for checking only. Use the exact column for anything you cut.

Common mistakes with fraction charts

  • Reading the wrong row in a long chart. 5/16 and 5/64 look alike at a glance. Check the decimal: 5/16 is 0.3125 in, while 5/64 is 0.078125 in.
  • Converting the fraction but forgetting the whole inches. 2 3/4 in is 69.85 mm, not 19.05 mm.
  • Rounding twice. Converting 9/32 in to 7.1 mm and then converting that rounded value back gives 0.27953 in, which is no longer exactly 9/32. Convert once from the original fraction.
  • Mixing a decimal foot with a decimal inch. 0.5 ft is 6 in, not 1/2 in.
  • Treating the mm column as a cutting tolerance. Three decimals are there for arithmetic only.

Can I enter fractions directly in Kerflio?

Yes. The free web planners, the sheet cut planner and the linear cut planner, accept decimals in millimetres and decimals or mixed fractions in inches. Choose the unit before you type, then enter sizes as you would write them, for example 23 5/8. If you switch units later, the planner converts the dimensions you already entered. The page on fractions and units explains how conversions are kept consistent, and the inches to mm chart covers whole inches and long lengths.

Frequently asked questions

What is 1/64 inch in millimetres?

1/64 in is 0.015625 in, which is 0.397 mm. It is the smallest step in this chart.

What is 5/8 inch as a decimal?

5/8 in is 0.625 in, which is 15.875 mm.

Is 3/4 inch the same as 19 mm?

No. 3/4 in is exactly 19.05 mm, so it is 0.05 mm thicker than 19 mm and 1.05 mm thicker than 18 mm.

Should I round to 1/16 or 1/32 in a cut list?

Keep the exact value in the planner and round only when you mark the part. Use 1/32 when parts must fit between other parts or many small errors could add up.

Why does every 64th have an exact decimal?

Because 64 is a power of two, every fraction with 64 underneath ends after at most six decimal places. Fractions such as 1/3 never end.

How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.