How do I read the marks between two inches?
Most inch tapes used in woodworking divide each inch into 16 parts. The marks have different lengths so you can tell them apart without counting from zero every time. The half-inch mark is the longest after the inch line, the quarters are shorter, the eighths shorter again and the sixteenths are the shortest. Some tapes add 1/32 marks, so check your blade before counting.
| Fraction | In 16ths | Mark type | Millimetres |
|---|---|---|---|
| 1/16 | 1/16 | Sixteenth (shortest) | 1.588 |
| 1/8 | 2/16 | Eighth inch | 3.175 |
| 3/16 | 3/16 | Sixteenth (shortest) | 4.762 |
| 1/4 | 4/16 | Quarter inch | 6.350 |
| 5/16 | 5/16 | Sixteenth (shortest) | 7.938 |
| 3/8 | 6/16 | Eighth inch | 9.525 |
| 7/16 | 7/16 | Sixteenth (shortest) | 11.112 |
| 1/2 | 8/16 | Half inch | 12.700 |
| 9/16 | 9/16 | Sixteenth (shortest) | 14.288 |
| 5/8 | 10/16 | Eighth inch | 15.875 |
| 11/16 | 11/16 | Sixteenth (shortest) | 17.463 |
| 3/4 | 12/16 | Quarter inch | 19.050 |
| 13/16 | 13/16 | Sixteenth (shortest) | 20.638 |
| 7/8 | 14/16 | Eighth inch | 22.225 |
| 15/16 | 15/16 | Sixteenth (shortest) | 23.813 |
| 1 | 16/16 | Inch line (longest) | 25.400 |
To read a measurement, note the last whole inch, then find the longest mark you have passed and count small marks from there. If the end of the board sits two small marks past the half inch, it is 8/16 + 2/16 = 10/16, which reduces to 5/8.
The board ends after the 23 in line.
It has passed the 3/4 mark (12/16) and sits on the next sixteenth mark after it.
12/16 + 1/16 = 13/16, so the reading is 23 13/16 in.
Converted: 23 13/16 = 23.8125 in, which is 604.838 mm.
What are the marks every 16 inches?
Many inch tapes highlight every 16 in as a stud center marking for framing. Stanley lists 16 in and 19.2 in stud center markings on several of its tapes. The 19.2 in spacing is marked with a small black diamond on Stanley blades, and Stanley describes it as a spacing used for engineered joists.
| Mark | 16 in spacing | Feet and inches | mm | 19.2 in spacing | mm |
|---|---|---|---|---|---|
| 1 | 16 in | 1 ft 4 in | 406.4 | 19.2 in | 487.68 |
| 2 | 32 in | 2 ft 8 in | 812.8 | 38.4 in | 975.36 |
| 3 | 48 in | 4 ft | 1,219.2 | 57.6 in | 1,463.04 |
| 4 | 64 in | 5 ft 4 in | 1,625.6 | 76.8 in | 1,950.72 |
| 5 | 80 in | 6 ft 8 in | 2,032.0 | 96 in | 2,438.40 |
| 6 | 96 in | 8 ft | 2,438.4 |
Both series land on 96 in: six 16 in spaces and five 19.2 in spaces each make 8 ft. You will rarely need these marks for a cut list. They help when you lay out shelf standards or wall cleats on a stud wall. A highlighted 16 or 32 is on the same inch scale as every other number.
Source: Stanley 12 ft PowerLock tape (33-312), 16 in and 19.2 in stud center markings, checked 2026-11-14.
Source: Stanley support: what the black diamond on a tape means, checked 2026-11-14.
Why does the hook at the end move?
The loose hook is deliberate. It slides by its own thickness so the tape reads correctly from the same zero whether you hook it over an edge (outside measurement) or push it against a surface (inside measurement). Pulled out, the hook adds its thickness to the gap. Pushed in, it closes that gap. Stanley calls this a true zero hook.
Hook play only works if the rivets and hook are not bent. A dropped tape can kink the hook so it no longer moves by exactly its thickness. Two quick checks help:
- Inside and outside on one block. Measure a square block by hooking one end, then by pushing the hook against a stop with the block butted to it. Both readings should agree.
- Against a steel rule. Hook the tape on a squared edge, lay a steel rule beside it, and compare the 6 in or 150 mm marks.
If you do not trust the hook, measure from a whole mark instead. Line the 1 in mark (or the 100 mm mark on a metric tape) up with one end and subtract it from the reading. Woodworkers call this burning an inch. Write the subtraction down, because forgetting it makes every part 1 in or 100 mm too long. Use the same method for every part in the job so the error, if any, is the same on all of them.
Source: Stanley support: why the hook on a tape measure moves, checked 2026-11-14.
How do I read a metric tape?
A metric tape is easier to read because every division is decimal. The longest marks are centimetres, numbered 1, 2, 3 or 10, 20, 30 depending on the brand, with a mid-length mark at each 5 mm and short marks at each millimetre. Read the last numbered centimetre, then count millimetres. If the tape numbers in centimetres, multiply by ten for a millimetre cut list: 63.7 cm is 637 mm.
The end of the part is past the 63 cm number.
It is past the mid-length 5 mm mark after 63 and two short marks beyond it.
630 + 5 + 2 = 637 mm.
Pick millimetres for the whole project rather than mixing centimetres and millimetres. A cut list with 637 next to 63.7 is an easy way to cut a part ten times too short. If your tape has inches on one edge and millimetres on the other, decide which edge you are using before you start and stick to it. The inches to mm chart covers the conversion when a drawing and a tape disagree.
How do I read a tape the same way for a whole cut list?
Consistency across all the parts matters most. If every part is 1/32 in long in the same way, a cabinet still goes together square. Errors in different directions are what open gaps.
- Use one tape for the job. Two tapes can disagree at their hooks. If you must change, check them against each other first.
- Look straight down at the mark. Reading from an angle shifts the mark against the edge by the thickness of the blade.
- Mark with a knife or a fine V. A thick pencil line can cover a sixteenth on its own. Put the point of the V on the mark.
- Decide which side of the line you cut. The saw removes a kerf on one side of the mark. Keep the kerf on the waste side every time. See saw kerf.
- Write the unit and the fraction in full. Write 23 13/16 in or 605 mm, never just 23 13.
- Measure repeated parts with a stop. For several identical parts, set a stop block from the first part rather than measuring each one with the tape.
What mistakes are most common when reading a tape?
- Counting sixteenths from the wrong long mark, which gives answers off by exactly 1/4 or 1/8.
- Misreading 6 and 9 or 66 and 99 when the tape is upside down. Some tapes print numbers on both edges to help.
- Reading the foot marker instead of the inch number. On some tapes 12 in also shows 1 ft, so 2 ft 3 in can be mistaken for 23 in.
- Letting the blade sag over a long span, which makes the reading longer than the straight distance. Support the tape or use a rule for long inside measurements.
- Forgetting a burned inch, as described above.
Where does this go in a cut plan?
Measure your stock as carefully as your parts. A board labelled 8 ft or a sheet labelled 2440 mm is not always that long after you square a rough end. Enter the usable length you measured, add the kerf you measured using measure your saw kerf, and then plan. The linear cut planner and sheet cut planner accept mixed fractions such as 23 13/16, so you can type the tape reading as you read it.
For sheet goods, measure the length and width at both ends and in the middle. A sheet that is slightly out of square or has a damaged corner gives a different reading at each end, and the smallest reading is the one to plan with. Write it on the sheet in pencil so you do not have to measure again.
Frequently asked questions
How many marks are in an inch on a tape?
Most woodworking tapes divide each inch into 16. Some add 1/32 marks.
Why are some numbers in red every 16 inches?
They are stud center markings for framing. Stanley lists 16 in and 19.2 in stud markings on several of its tapes.
Is the loose hook on my tape broken?
Usually not. It slides by its own thickness so inside and outside measurements both read from true zero. Check it if the tape has been dropped.
What does burning an inch mean?
Measuring from the 1 in mark instead of the hook, then subtracting 1 in from the reading. It avoids errors from a bent hook.
Should I use inches or millimetres?
Either works. Use one unit for the whole project and write the unit next to every number.
How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.