What is the actual thickness of 3/4 plywood?

Structural panels in the US are labelled by Performance Category. APA explains that since 2008 plywood carries both a Performance Category, which acts as the nominal thickness in the building codes, and a decimal thickness for packaging and labelling rules. A panel you would call "three-quarter" is usually stamped 23/32 PERF CAT.

Source: APA plywood overview, checked 2026-11-14.

The table below is PS 2-10 Table 1, as quoted by Huber Engineered Woods. It gives the thickness range each category must meet. The exact mm column is plain conversion arithmetic (1 in = 25.4 mm).

PS 2 Performance Categories and allowed thickness
Performance CategoryExact conversionMinimum, in (mm)Maximum, in (mm)
7/160.4375 in, 11.11 mm0.406 (10.32)0.469 (11.91)
1/20.5 in, 12.70 mm0.469 (11.91)0.531 (13.49)
19/320.59375 in, 15.08 mm0.563 (14.29)0.625 (15.88)
5/80.625 in, 15.88 mm0.594 (15.08)0.656 (16.67)
23/320.71875 in, 18.26 mm0.688 (17.46)0.75 (19.05)
7/80.875 in, 22.23 mm0.831 (21.11)0.919 (23.34)
11 in, 25.40 mm0.950 (24.13)1.05 (26.67)
1-1/81.125 in, 28.58 mm1.069 (27.15)1.181 (30.00)

Source: Huber Engineered Woods technical tip quoting PS 2-10 Table 1, checked 2026-11-14. Huber states a tolerance of ±1/32 in (0.8 mm) on categories of 13/16 in and less, and ±5% above that.

Two panels with the same stamp can therefore differ by more than 1/16 in. That is why the rest of this page keeps saying "measure".

How thick is 18 mm birch plywood?

Metric birch plywood is closer to its name, but it still has a range. Riga Wood publishes the ply count and the lower and upper thickness limits for each nominal size of its Riga Prime birch plywood, measured at 9 ± 3% moisture content.

Birch plywood nominal thickness, plies and limits (Riga Prime)
Nominal (mm)PliesLower limit (mm)Upper limit (mm)Nearest fraction
6.556.16.9about 1/4 in
978.89.5about 11/32 in
12911.512.5about 15/32 in
151114.315.3about 19/32 in
181317.118.1about 23/32 in
211520.020.9about 13/16 in
241722.923.7about 15/16 in

Source: Riga Wood (Latvijas Finieris) Riga Prime birch plywood data sheet, checked 2026-11-14.

The "nearest fraction" column is the closest 1/32 in to the nominal size, for shopping only. 18 mm is 0.709 in, between 11/16 (0.6875) and 23/32 (0.719), and nowhere near 3/4 (0.75). Never set a dado cutter to a fraction because a metric sheet is "about" that size. WISA lists the same nominal birch thicknesses (6.5 to 50 mm) and states that all of its plywood thicknesses are nominal.

Source: WISA sizes, thicknesses and weights, checked 2026-11-14.

What thicknesses are sold in Canada?

Canadian softwood plywood is made in metric thicknesses. The Canadian Plywood Association lists sanded panels from 6 mm to 30 mm and sheathing and select panels from 7.5 mm to 31.5 mm.

CANPLY EXTERIOR plywood thicknesses
TypeThicknesses (mm)
Sanded6, 8, 11, 14, 17, 19, 21, 24, 27, 30
Sheathing and select7.5, 9.5, 11, 12.5, 15.5, 18.5, 20.5, 22.5, 25.5, 28.5, 31.5

Source: Canadian Plywood Association, Plywood Design Fundamentals, checked 2026-11-14. The same document says some of these approximate imperial sizes, for example 6 mm for 1/4 in.

So a Canadian "3/4" sanded panel is likely to be 19 mm, while a sheathing panel used for a shop cabinet may be 18.5 mm. Same job, two different groove widths.

How many plies does hardwood plywood have?

Ply count depends on the core. Roseburg's hardwood plywood sheet lists veneer core panels at 3 plies for 1/4 in, 5 plies for 3/8 and 1/2 in, and 7 plies for 5/8 and 3/4 in. Its particleboard and MDF core panels are listed as 3 plies: a core with a face and back veneer. Roseburg refers thickness tolerances to the ANSI/HPVA HP-1-2016 hardwood plywood standard.

Source: Roseburg hardwood plywood technical data sheet, checked 2026-11-14.

For the cut list, the point is that two "3/4" hardwood panels with different cores can measure differently, so measure each stack. MDF vs plywood for cabinets compares the core materials.

Why does actual thickness matter for dados and grooves?

A dado cut to the nominal size leaves a gap when the panel is thinner. The gap shows as a loose joint and a visible line along the front edge.

Worked example: 3/4 in dado for a thinner panel

Suppose your calipers read 0.703 in on the shelf panel.

Dado width 0.75 in − panel 0.703 in = 0.047 in gap.

0.047 in × 25.4 = 1.19 mm, a little over 3/64 in.

Cut the dado to the measured panel, not the label. Many woodworkers cut a test groove in scrap and slide the real panel in before cutting the project parts. For grooves that take a back panel, measure the back panel too: thin sheets have their own tolerances.

How does panel thickness change the cut list?

Any part that spans between two other parts gets its length from their thickness. Get the thickness wrong and fixed shelves, cabinet bottoms and stretchers come out short or long.

Worked example: inside width of a 24 in cabinet

Outside width 24 in. Sides nominal 3/4 in: 24 − 0.75 − 0.75 = 22.5 in inside.

Sides measured at 23/32 in (0.71875 in): 24 − 0.71875 − 0.71875 = 22.5625 in inside.

A bottom cut at 22-1/2 in is 1/16 in short. If the bottom sits in 1/4 in deep dados, its length is 22.5625 + 0.25 + 0.25 = 23.0625 in, or 23-1/16 in.

Worked example: inside width of a 600 mm cabinet

Outside width 600 mm. Sides nominal 18 mm: 600 − 18 − 18 = 564 mm.

Sides measured at 17.6 mm: 600 − 17.6 − 17.6 = 564.8 mm.

A fixed shelf cut at 564 mm leaves a 0.8 mm gap.

Kerflio does not calculate joinery. You work out the part sizes, then enter them. How to make a cut list covers the full process, and fractions and units helps when the drawing is in inches and the sheet is metric.

How should I measure plywood thickness?

Use calipers rather than a tape. WISA's measuring note, which follows EN 324-1, takes readings 50 mm in from the edge at eight points and averages them, rounding to 0.1 mm. You do not need eight points in a home shop, but a few readings away from the edge tell you more than one reading at a corner.

Source: WISA sizes, thicknesses and weights, checked 2026-11-14.

  • Measure at least three spots per sheet, away from the edges, where crushing from handling is common.
  • Write the average on the sheet in pencil, with the date.
  • Measure again if the sheet has sat in a damp place. Thickness changes with moisture.
  • Keep sheets from different stacks in separate stock groups if they measure differently.

What about thin panels for backs and drawer bottoms?

Thin sheets have the same label problem, and a groove for a back panel is narrow enough that a fraction of a millimetre shows. The sources on this page list these thin sizes:

  • Roseburg hardwood plywood: 1/4 in with 3 plies on a veneer core.
  • CANPLY sanded plywood: 6 mm, which the association says approximates 1/4 in.
  • Riga Prime birch: 6.5 mm nominal, 5 plies, 6.1 to 6.9 mm.

Source: Roseburg hardwood plywood technical data sheet, checked 2026-11-14.

Source: Canadian Plywood Association, Plywood Design Fundamentals, checked 2026-11-14.

Source: Riga Wood (Latvijas Finieris) Riga Prime birch plywood data sheet, checked 2026-11-14.

Worked example: back panel groove

A 1/4 in groove is 0.25 × 25.4 = 6.35 mm wide.

Suppose your back panel measures 5.5 mm. The gap is 6.35 − 5.5 = 0.85 mm.

A back that rattles in its groove is common. Cut the groove to the measured panel, or plan to glue or pin the back.

The same thin sheet also changes the depth of the parts around it. If the back sits in a rabbet, the depth of the cabinet sides and bottom is measured to the back of the rabbet, not to the back of the sheet.

Which thickness do I type into Kerflio?

Kerflio uses thickness to match parts to stock: a part is only placed on stock of the same material and thickness. It does not use thickness to resize anything. So pick one consistent value per stack and use it for both the stock row and its parts.

  • If you measured 17.6 mm, enter 17.6 for the sheet and for every part cut from it.
  • If you prefer to type the nominal 18, do so everywhere, and keep the measured value in your joinery notes.
  • Do not enter 18 on the stock and 17.6 on the parts. They will not match, and the parts will show as unplaced.

For converting between fractions and millimetres, the fractions and units page shows the method.

Common thickness mistakes

  • Cutting every dado at the nominal fraction because the plan says 3/4.
  • Mixing 18 mm birch and 23/32 in domestic plywood in one cabinet and then wondering why the reveals differ.
  • Converting 18 mm to 3/4 in exactly. 3/4 in is 19.05 mm.
  • Measuring one sheet and assuming the rest of the stack matches.
  • Forgetting edge banding, which adds to the part's size. See the edge banding allowance guide.

Frequently asked questions

Is 23/32 plywood the same as 3/4 plywood?

23/32 is the Performance Category stamp on most panels sold as 3/4 in. Under PS 2 a 23/32 panel may measure from 0.688 to 0.75 in, so it can be thinner than 3/4 in.

How thick is 18 mm plywood in inches?

18 mm is about 0.709 in, between 11/16 and 23/32 in. Riga Wood lists its 18 mm birch plywood at 17.1 to 18.1 mm.

How many plies does 18 mm birch plywood have?

Riga Wood lists 13 plies for 18 mm Riga Prime birch plywood. Other makers and grades may differ.

Should I enter nominal or actual thickness in a cut list?

Use the measured thickness wherever a part fits between others or into a groove. The thickness also keeps stock groups apart, since parts can only come from matching stock.

Why is my plywood thicker than the label?

The standards allow plus as well as minus. The PS 2 range for 23/32 runs up to 0.75 in, and moisture can swell a sheet.

How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.