How thick is edge banding?

Thickness depends on the material and the job. These figures come from maker literature checked for this page.

Edge band thicknesses published by makers
BandThicknessIn inchesPublished by
Thin ABS, unglued or pre-glued, 23 mm wide0.4 mm0.016 inEGGER
Pre-glued wood veneer0.55 mm ± 0.05 mm, without the hot melt0.022 inTECE Dekor
ABS, 23 or 43 mm wide0.8 mm0.031 inEGGER
ABS, 21 mm wide1 mm0.039 inLaminex
ABS, 43 mm wide1.5 mm0.059 inEGGER
ABS, 22, 29 or 38 mm wide2 mm0.079 inLaminex
ABS, 23, 28, 43 or 54 mm wide2 mm0.079 inEGGER

Source: EGGER Availability Guide (copy hosted by a distributor), checked 2026-11-14.

Source: Laminex product page (White Natural, all formats), checked 2026-11-14.

Source: TECE Dekor pre-glued veneer edgebanding specification, checked 2026-11-14. TECE gives widths such as 18, 22 and 38 mm and an EVA hot melt backing.

The inch column is conversion arithmetic (thickness ÷ 25.4), rounded to three places. Rolls sold in inch markets may list a different nominal thickness, so measure a short offcut of your band with calipers, glue side included if it is pre-glued.

Which band thickness goes on which edge?

Ostermann, a European edging supplier, suggests 0.4 mm ABS for rear panels and shelves, 1 mm ABS for carcasses and fronts, and 2 mm ABS for tables and edges that take knocks. That is one supplier's guidance, not a rule, but it is a sensible starting point.

Source: Ostermann: the right edging for each project, checked 2026-11-14.

  • Front edges of shelves and cabinet sides: the edge you see. Band it.
  • Door and drawer front edges: usually all four, because every edge shows when the door opens.
  • Back edges of shelves and sides: often left bare when they sit against a back panel or wall.
  • Ends of a shelf that sit in a dado or against a side: left bare, so the shelf length is not reduced.
  • Tops that people lean on or bump: a thicker band, or solid wood edging. See solid wood edging allowance.

How do I calculate the cut size?

Work out each dimension on its own. Count how many of its two ends get a band, and subtract that thickness for each.

cut length = finished length − band on end 1 − band on end 2same rule for width
Worked example: shelf banded on the front edge, 2 mm ABS

Finished size 564 × 300 mm, length side to side, width front to back.

Length: ends sit against the cabinet sides, no band. Cut length 564 mm.

Width: front edge banded, back edge bare. 300 − 2 = 298 mm.

Cut size: 564 × 298 mm.

Worked example: door banded on four edges, 1 mm ABS

Finished size 716 × 396 mm.

Length: 716 − 1 − 1 = 714 mm. Width: 396 − 1 − 1 = 394 mm.

Cut size: 714 × 394 mm.

Worked example: cabinet side with 0.8 mm ABS on the front edge

Finished size 720 × 560 mm, grain along 720.

Length: top and bottom edges hidden, no band. 720 mm.

Width: front edge banded. 560 − 0.8 = 559.2 mm.

Most saws cannot hit 0.2 mm. Cutting 559 mm gives a finished depth of 559.8 mm, which is usually fine for a side.

What does it look like in inches?

Convert the band to inches first, then subtract. With 2 mm bands the change is easy to see. With thin veneer it often falls under 1/32 in.

Worked example: door banded all round with 2 mm PVC or ABS

2 mm ÷ 25.4 = 0.0787 in per edge, 0.1575 in for two edges.

Finished 28 × 15-1/2 in.

Length: 28 − 0.1575 = 27.8425 in, closest 1/32 is 27-27/32 in (27.84375).

Width: 15.5 − 0.1575 = 15.3425 in, closest 1/32 is 15-11/32 in (15.34375).

Worked example: shelf front with pre-glued veneer

0.55 mm ÷ 25.4 = 0.0217 in.

Finished depth 11-1/4 in: 11.25 − 0.0217 = 11.2283 in.

0.0217 in is less than 1/32 in (0.03125), so most people cut 11-1/4 in and accept a finished shelf that is a hair deeper.

Fractions and units has the conversion steps, and Kerflio accepts fractions directly, so you can type 27 27/32.

When can I ignore the band thickness?

Ignore it when the error is smaller than you can cut and nothing depends on the exact size. A 0.55 mm veneer on the front of a loose shelf is a good example. Do not ignore it when:

  • The band is 1 mm or thicker and the part fits an opening, such as an inset door or a drawer front between rails.
  • Bands add up across a row. Four inset doors in a run, each banded both sides with 2 mm, gain 16 mm in total.
  • Parts must line up with something unbanded, such as a cabinet side flush with a face frame.

How do I write banding in a cut list?

Keep the cut size and the finished size both in the list, and say which edges get a band. Many cabinet shops use edge codes: L1 and L2 for the two long edges, W1 and W2 for the two short edges. Any consistent code works.

Example rows with banding notes
LabelQtyCut L × W (mm)Finished (mm)BandRotate
Shelf8564 × 298564 × 300L1 2 mmNo
Door2714 × 394716 × 396L1 L2 W1 W2 1 mmNo
Side2720 × 559720 × 560W1 0.8 mmNo

Enter the cut size in the planner. Kerflio places rectangles and counts kerf, and it does not apply banding for you. Put the banding code in the part label, such as "Shelf L1 2mm", so it shows on the layout. The CSV format page shows which columns the app imports.

Can banding change the number of sheets?

Yes, when parts sit right at the edge of fitting. Subtracting the band makes each part smaller, and a row of small savings can let one more part into a strip.

Worked example: six narrow parts across a 1220 mm sheet, 3 mm kerf

Finished width 201 mm each, so without allowing for bands: 6 × 201 + 5 × 3 = 1221 mm. One millimetre too wide.

Banded on both long edges with 1 mm ABS, the cut width is 201 − 1 − 1 = 199 mm: 6 × 199 + 5 × 3 = 1209 mm. All six fit.

The reverse also happens. If you forget the band and cut at the finished size, the parts come out too big after banding, and you may have planned a layout that wastes material. Always plan with cut sizes.

What about the glue line?

A pre-glued band has a layer of hot melt on its back. TECE states its veneer thickness without the glue and puts about 300 g of EVA hot melt on each square metre of band. Once the band is pressed on, part of that layer stays in the joint. You cannot know how much from the label, so do a test: band an offcut, trim it, and measure the finished part. Use the difference between before and after as your allowance.

Source: TECE Dekor pre-glued veneer edgebanding specification, checked 2026-11-14.

How much banding do I need?

Add up the banded edge lengths, then add a trimming allowance per edge. The allowance is your choice. The examples below use 25 mm per edge to show the arithmetic, not as a recommendation.

Worked example: banding for 2 doors and 8 shelves

One door: 716 + 716 + 396 + 396 = 2224 mm of edge, plus 4 × 25 = 100 mm, so 2324 mm. Two doors: 4648 mm of 1 mm band.

Shelves: 8 × (564 + 25) = 4712 mm of 2 mm band.

Keep the two thicknesses as separate totals, because they come on separate rolls.

Common banding mistakes

  • Subtracting the band once for a part banded on both ends of a dimension.
  • Subtracting the band from shelf length when the ends are not banded.
  • Forgetting that a pre-glued band's listed thickness may exclude the glue layer, as TECE's specification does.
  • Using the finished size in the planner, then trimming the band flush and ending up oversize.
  • Not asking how much an edgebanding machine trims from the panel edge before applying the band, if a shop is banding your parts.

Thickness matters for the panel itself too: see the plywood thickness chart.

Frequently asked questions

Do I subtract edge banding from the cut size?

Yes, for bands thick enough to matter. Subtract the band thickness once for each banded edge along a dimension, so a part banded on both long edges loses two thicknesses from its width.

How thick is iron-on wood veneer edge banding?

TECE Dekor lists its pre-glued veneer band at 0.55 mm ± 0.05 mm without the hot melt, about 0.022 in. Measure your own roll, glue side included.

What thickness of edge banding should I use for cabinet doors?

Ostermann suggests 1 mm ABS for carcasses and fronts and 2 mm ABS for tables and edges that take knocks. Match the band to how hard the edge will be used.

Does Kerflio add edge banding automatically?

No. Enter the cut size after subtracting the band. Keep the band code in the part label.

Can I ignore 0.5 mm edge banding?

Often, for loose parts like shelves, because it is under 1/32 in. Do not ignore it for inset doors or rows of parts where small amounts add up.

How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.