How do I size the plywood core?
The core is the finished size minus the edging on every edge that gets it. If a shelf has 6 mm edging on its front only, the core is 6 mm shallower than the shelf and the same length.
This is the same subtraction as edge banding allowance, with one difference: the edging is thick enough that you can never ignore it, and it is applied oversize and trimmed afterwards.
How big should the edging strips be?
Each strip has three sizes to decide.
- Thickness (how far it adds to the panel). This is a design choice: thin enough to look neat, thick enough to protect the edge. Write it down once and use it everywhere.
- Height (across the panel thickness). Make it a little more than the plywood's measured thickness, so it stands proud of both faces and can be planed, scraped or routed flush. The plywood thickness chart explains why you measure the sheet first.
- Length. Cut it longer than the edge so the ends can be trimmed flush after glue-up.
The overhang allowances on this page (1.5 mm proud each face, 10 mm extra at each end) are examples to show the arithmetic. Choose your own based on your trimming method and how straight your strips are.
Worked example: plywood shelves with a front lip
Edging: 6 mm thick on the front edge only.
Core: length 764 mm (ends not edged), width 300 − 6 = 294 mm. Cut six cores at 764 × 294 mm.
Strip height: measured plywood 18 mm, strip 21 mm, so (21 − 18) ÷ 2 = 1.5 mm proud of each face.
Strip length: 764 + 10 + 10 = 784 mm.
Cut six strips at 784 × 21 × 6 mm, glue on, trim the ends flush to the core, then trim the faces flush.
If the plywood measures 17.6 mm instead of 18, the same 21 mm strip stands (21 − 17.6) ÷ 2 = 1.7 mm proud of each face. Still fine, which is why a few millimetres of extra height is easier than an exact match.
The core goes into the sheet planner as 764 × 294 mm with the grain along 764 and rotation off. The strips go into the linear planner, below.
How do I make a linear cut list for the edging?
Edging strips are lengths, so plan them like boards. List each strip at its oversize length, enter your board length and kerf, and let the linear planner place them.
Three strips per length: 3 × 784 + 2 × 3 = 2358 mm, which fits in 2400 mm with 2400 − 2358 = 42 mm left.
Four would need 4 × 784 + 3 × 3 = 3145 mm, so three is the most.
Six strips ÷ 3 per length = 2 lengths of 2400 mm stock.
If you rip the strips yourself from a wider board, work out the count across the board's width separately. Each strip costs its own thickness plus one kerf. For a 95 mm wide board ripped into 6 mm strips with a 3 mm kerf, the arithmetic allows 10 strips (10 × 6 + 9 × 3 = 87 mm), before any material you remove to straighten the edge between rips. Follow your saw's manual for ripping thin strips. Sheet vs linear cutting explains which planner handles which part of the job.
Worked example: a desk top edged on three sides
A top 1200 × 600 mm finished, with 10 mm edging on the front and both ends. The back sits against a wall and stays bare.
Length: 1200 − 10 − 10 = 1180 mm.
Width: 600 − 10 = 590 mm (front edged, back bare).
Core: 1180 × 590 mm.
End strips cover the core's ends: finished length 590 mm, cut 590 + 10 = 600 mm and trim flush at the back.
Front strip covers the core plus both end strips: finished 1200 mm, cut 1200 + 10 + 10 = 1220 mm.
End strips run to the front corner: finished length 600 mm, measured on the outside face.
Front strip: finished length 1200 mm on the outside face.
Cut each strip with extra length and fit the mitres before glue-up. The extra is your choice.
The butt joint version is easier to size and trim. The mitre version hides end grain at the corners. Either way, the core stays 1180 × 590 mm.
Worked example in inches
Finished 30 × 11-1/4 in, plywood stamped 23/32 in.
Core: length 30 in, width 11-1/4 − 1/4 = 11 in.
Strip height 13/16 in: (26/32 − 23/32) ÷ 2 = 3/64 in proud of each face.
Strip length: 30 + 3/8 + 3/8 = 30-3/4 in.
Kerflio reads fractions such as 30 3/4, so you can enter the list as written. Fractions and units covers mixed inputs.
Should I edge first and then cut the panel to length?
There are two ways, and both work.
- Cut the core to final length, glue on an oversize strip, then trim the strip ends flush to the core. The core size in the cut list is final.
- Cut the core oversize in length, glue the edging on, then cut the edged panel to final length in one pass. Core and strip end up flush because they are cut together.
Finished shelf 764 mm long. Add 10 mm to the core: 774 × 294 mm.
Four shelves need 4 × 774 = 3096 mm of core length before kerf.
After edging, cut each shelf to 764 mm.
The second method uses a little more plywood. Write the oversize in the cut list label so nobody cuts the core to final length by mistake, for example "Shelf core +10".
What if both long edges get edging?
A free-standing shelf, a bench top or a table top is often edged front and back. Subtract the edging twice from the width.
Core width: 400 − 10 − 10 = 380 mm.
Two strips per top, each at the top's length plus your trimming allowance.
If the ends are edged too, subtract the end strips from the core length the same way, and decide which strips run past the others at the corners.
Count the strips carefully in the linear list. A top edged on four sides needs four strips, in two lengths.
Does edging work on MDF?
Yes, the arithmetic is identical. MDF edges are plain, so many people paint them and skip edging. Solid edging on MDF shelves or tops is still common where the edge will take knocks. The core is cut smaller by the edging thickness in the same way, and the stock group is MDF of the measured thickness. See MDF vs plywood for cabinets for how the board choice changes the rest of the cut list.
Checklist and common mistakes
Before glue-up, check:
- Core cut to finished size minus the edging, or oversize by the amount written on its label.
- Strips taller than the measured panel thickness.
- Strips longer than the edge they cover.
- Strip grain running along its length.
- Every strip in the list, including both ends of tops edged on three or four sides.
Mistakes that show up after glue-up:
- Cutting the core at the finished size, so the edged shelf ends up 6 mm too deep and no longer fits the cabinet.
- Subtracting the edging from the shelf length when only the front is edged.
- Making the strip exactly as tall as the nominal plywood thickness. If the sheet is thicker than you expect, the strip sits below the face.
- Running the strip grain across the strip. Cut edging with the grain along its length.
- Planning strips at their finished length, then having nothing left to trim.
- Forgetting the strips entirely when buying timber. Add them to a separate linear list.
Frequently asked questions
How much should solid wood edging overhang?
Enough to trim flush with your method. This page uses 1.5 mm proud of each face and 10 mm extra at each end as examples. Pick allowances that suit your tools.
Do I cut the plywood smaller for solid edging?
Yes. Subtract the edging thickness from the core for every edged side. A shelf 300 mm deep with a 6 mm front lip needs a 294 mm deep core.
Which planner do I use for the edging strips?
Use a linear planner, because strips are lengths. Enter each strip at its oversize length and the board length you have.
Is solid edging better than edge banding?
It is thicker, so it takes knocks and can be shaped or rounded. It also takes more work and more material. Banding is quicker for many parts.
Should the edging be wider than the plywood thickness?
A little wider makes trimming easier, because you can plane or rout it flush to both faces. Measure the plywood first, since its real thickness may differ from the label.
How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.