Kerf chart from product specifications
Each row below is one specific blade, with the kerf exactly as its maker publishes it and the conversion to the other unit. A blade of the same type from another maker can be wider or narrower, so read the kerf on your own blade's page or packaging. For what kerf is and why a plan needs it, see saw kerf explained.
| Tool and type | Blade | Published kerf | Inches | mm | Source |
|---|---|---|---|---|---|
| Table saw, full kerf | Forrest Woodworker II, 10 in, 40 teeth (WW10407125) | 0.125 in | 0.125 | 3.18 | Forrest product page |
| Table or mitre saw, thin kerf | Diablo D1050X, 10 in, 50 teeth | 0.098 in | 0.098 | 2.49 | Diablo product page |
| Circular saw, 7 1/4 in | Diablo D0724A, 7 1/4 in, 24 teeth framing | 0.059 in | 0.059 | 1.50 | Diablo product page |
| Plunge (track) saw, 6 1/2 in | Makita A-99960, 6 1/2 in, 28 teeth | 0.079 in | 0.079 | 2.01 | Makita product page |
| Plunge (track) saw, 160 mm | Festool 496302, HW 160×2.2×20 W28 | 2.2 mm | 0.087 | 2.20 | Festool product page |
| Plunge (track) saw, 160 mm | Festool 205551, HW 160×1.8×20 W28 | 1.8 mm | 0.071 | 1.80 | Festool product page |
Sources: the product page linked in each row, checked 2026-11-14. Retail listings sometimes disagree with the maker; these values come from the makers' own pages.
What is the difference between full kerf and thin kerf?
Full kerf for a 10 in table saw blade is the 1/8 in (0.125 in, 3.175 mm) shown by the Forrest blade. Thin-kerf blades are narrower. The Diablo D1050X is listed at 0.098 in, close to 3/32 in (0.09375 in). Thin kerf has no fixed width, so look up the figure for your blade.
Per cut the difference is small: 0.125 − 0.098 = 0.027 in (0.686 mm). It adds up when a plan has many cuts in a row, such as ripping strips or cutting many short parts from one board.
| Blade | 10 cuts (in) | 10 cuts (mm) | 30 cuts (in) | 30 cuts (mm) |
|---|---|---|---|---|
| Forrest Woodworker II | 1.250 | 31.8 | 3.750 | 95.3 |
| Diablo D1050X | 0.980 | 24.9 | 2.940 | 74.7 |
| Diablo D0724A | 0.590 | 15.0 | 1.770 | 45.0 |
| Makita A-99960 | 0.790 | 20.1 | 2.370 | 60.2 |
| Festool 496302 | 0.866 | 22.0 | 2.598 | 66.0 |
| Festool 205551 | 0.709 | 18.0 | 2.126 | 54.0 |
The blade you choose also depends on the saw. Festool lists the 2.2 mm 496302 blade for the TS 55, TSC 55, ATF 55 and AP 55, and the 1.8 mm 205551 blade for the TS 55 F, TSC 55 K and related saws. Follow your saw's manual on which blades it accepts. Kerflio needs only the number. If you own two saws, look up both blades and plan each job with the one you will actually use, because a 1/8 in table saw kerf and a 1.8 mm track saw kerf differ by 1.375 mm on every cut.
How do I read a blade label such as 160×2.2×20?
Festool names its blades by three numbers in millimetres: diameter, cutting width and bore. On the 496302 product page, HW 160×2.2×20 W28 matches a 160 mm diameter, a 2.20 mm cutting width, a 20 mm bore and 28 teeth. The cutting width is the kerf. Other makers print the kerf as a separate line, in inches with three decimals on the Diablo and Makita pages, and list the plate thickness nearby. The plate is thinner than the kerf because the teeth are wider than the body of the blade. Enter the kerf, not the plate.
If you mark parts with an inch tape, it helps to know the kerf as a fraction. The table rounds each published kerf to the nearest 1/64 in.
| Blade | Kerf (in) | Nearest 1/64 in | Difference (mm) |
|---|---|---|---|
| Forrest Woodworker II | 0.1250 | 1/8 | 0.000 |
| Diablo D1050X | 0.0980 | 3/32 | −0.108 |
| Diablo D0724A | 0.0590 | 1/16 | +0.089 |
| Makita A-99960 | 0.0790 | 5/64 | −0.022 |
| Festool 496302 | 0.0866 | 3/32 | +0.181 |
| Festool 205551 | 0.0709 | 5/64 | +0.184 |
A fraction is handy for checking a test cut with a rule. For the planner, enter the decimal or the millimetre value so the small differences in the last column stay out of the plan.
When does a different kerf change the plan?
A smaller kerf only helps when the plan is close to the limit. Here is a case where it decides the outcome.
Eight strips of 302.5 mm across a 2440 mm length need eight strips and seven cuts between them.
With a 3.2 mm kerf: 8 × 302.5 + 7 × 3.2 = 2,442.4 mm. That is 2.4 mm more than the sheet, so the eighth strip will not fit.
With a 2.2 mm kerf: 8 × 302.5 + 7 × 2.2 = 2,435.4 mm, leaving 4.6 mm.
With a 1.8 mm kerf: 8 × 302.5 + 7 × 1.8 = 2,432.6 mm, leaving 7.4 mm.
3.2 mm is the metric figure Forrest gives for its 0.125 in blade. The sheet's factory edges are used as finished edges in this example. If you need to trim more than 4.6 mm in total from the length, the 2.2 mm plan no longer fits either. The count formula for boards is on how many pieces from a board.
Why does my measured kerf differ from the published number?
The published kerf is the width of the teeth on a new blade. The slot your saw actually cuts can be wider. A blade that wobbles, an arbor with runout, a fence not parallel to the blade, a dull blade or a sheet that moves during the cut all widen the slot. Some materials also close up or fray at the edge, which changes what you see.
Measure the real gap with a test cut and use that value in the plan. The method takes a few minutes and is on measure your saw kerf. If your measured value is wider than the published one by more than a small amount, that is worth looking into before a big job, using your saw's manual.
What about band saws and hand saws?
Band saw blades are sold by width, thickness and tooth set, and the kerf depends on the set and on how the blade tracks. It changes with each blade and setup, so this chart has no band saw row. Measure a test cut. The same applies to hand saws, where the set of the teeth and your technique both affect the slot.
For a sliding panel saw or a beam saw, use the kerf on the blade's specification sheet as a start and measure in the same way. With any saw, repeat the test cut after you change or sharpen the blade, because a resharpened blade can cut a slightly narrower slot than it did when new.
How do I choose a kerf value to enter?
- Use measured over published. Measure once per blade and setup and write the value on the blade's storage box.
- Round up, not down. If the measurement falls between 2.4 and 2.5 mm, enter 2.5 mm. A plan made with a kerf slightly too large leaves a little extra offcut; one made with a kerf too small can leave you a part short.
- One kerf per plan. If you will rip on the table saw and crosscut with a circular saw, plan with the wider kerf or split the job into separate plans for each saw.
- Keep trim separate. Kerf is the slot. Trimming a damaged edge is a separate allowance, entered by planning with the usable stock size.
Where do I enter the kerf in Kerflio?
Both free web planners have one kerf field for the whole job, in the same unit as your sizes. Try the strip example above in the sheet cut planner with 3.2 mm and then 2.2 mm and watch the count of placed parts change. The linear cut planner uses the same field for boards.
Frequently asked questions
How wide is a standard table saw blade kerf?
A full-kerf 10 in table saw blade is 1/8 in (0.125 in, 3.175 mm). The Forrest Woodworker II 10 in 40-tooth blade is listed at that width.
How wide is a thin-kerf blade?
It varies. The Diablo D1050X 10 in thin-kerf blade is listed at 0.098 in, close to 3/32 in.
What is the kerf of a 7 1/4 inch circular saw blade?
The Diablo D0724A framing blade is listed at 0.059 in (1.50 mm). Other blades differ, so check yours.
What is the kerf of a Festool track saw blade?
Festool lists 160 mm blades with 2.2 mm kerf (for example 496302) and 1.8 mm kerf (for example 205551). Each fits different saw models.
Should I enter the published kerf or my measured kerf?
Your measured kerf. It includes blade wobble and setup, which the published width does not.
How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.