Why does the cut order matter?

In a guillotine layout every cut runs from one edge of a piece to the opposite edge. That only works in one order. If you try to make a short crosscut before the long rip that should have freed its strip, the crosscut would have to stop partway across the sheet, which a straight edge-to-edge cut cannot do. The order also decides which pieces you handle, and how big they are when you cut them.

If guillotine layouts are new to you, read guillotine cuts explained first. This page assumes the layout is already fixed and asks only: which cut comes first?

What are parent cuts and child cuts?

Think of the layout as a tree. The full sheet is the root. Its first cut splits it into two pieces: those are its children. Each child can be split again, and so on, until every piece is either a finished part or an offcut. A parent cut is any cut that creates the piece another cut works in. A child cut works inside a piece made by an earlier cut.

Parent and child cuts in plain terms
TermMeaningExample on a sheet
RootThe full stock item before any cutThe 2440 × 1220 mm sheet
Parent cutA cut that creates a piece to be cut againA full-length rip that frees a 560 mm strip
Child cutA cut inside a piece made earlierA crosscut in that strip that frees one part
LeafA piece that is not cut againA finished part, or an offcut

The rule is simple: a cut can be made only after its parent. Two cuts in different branches do not depend on each other, so you can choose which branch to finish first.

Why do the longest rips usually come first?

In most cabinet-style layouts the first level of the tree is a set of rips along the sheet's length, because parts are grouped into strips of one width. Those rips are the parent cuts for everything else, so they come first. They are also the longest cuts in the job, and they are made while the sheet is still one piece.

Not every layout starts with rips. If the planner has grouped parts into crosscut panels first, the first level is crosscuts and the rips come inside them. Follow the tree, not a fixed habit. For choosing the first cut when you plan by hand, see breaking down plywood sheets.

How should I number the cuts?

Give each cut a number that shows its parent. One clear scheme: number the first-level cuts 1, 2, 3. Number the cuts inside the piece made by cut 1 as 1.1, 1.2, 1.3. A cut inside piece 1.2 would be 1.2.1. You can then read any cut's parent from its number, and you never make 1.2 before 1.

Number cuts in the order you will make them within each piece. Write the number on the sheet in pencil next to the line, and the part label on each piece the cut frees, so pieces do not get mixed up once they are off the saw. Kerflio's cut walkthrough lists parent cuts before the cuts inside them, in the same spirit.

Worked example: a cut tree from a 2440 × 1220 sheet

Job: three parts at 720 × 560 mm, two at 764 × 560 mm and one at 600 × 560 mm, all from one 2440 × 1220 mm sheet. Kerf 3 mm (an assumed value for this example; measure yours). All parts are 560 mm wide, so the layout groups them into two 560 mm strips.

Source: NBS Source: Hanson birch plywood product listing, checked 2026-11-14. It lists 2440 × 1220 mm and 3050 × 1525 mm sheets. Sizes vary by product and supplier, so measure the sheet you buy.

Worked example: first-level rips

Cut 1, rip at 560 mm: frees strip A, 2440 × 560. Left: 1220 − 560 − 3 = 657 mm.

Cut 2, rip at 560 mm in what is left: frees strip B, 2440 × 560. Left: 657 − 560 − 3 = 94 mm, an offcut strip 2440 × 94.

Worked example: crosscuts in strip A

Cuts 1.1, 1.2 and 1.3 each free a 720 × 560 part.

Used: 3 × 720 + 3 × 3 = 2169 mm. Left: 2440 − 2169 = 271 mm, an offcut 560 × 271.

Worked example: crosscuts in strip B

Cuts 2.1 and 2.2 free two 764 × 560 parts, cut 2.3 frees the 600 × 560 part.

Used: 764 + 764 + 600 + 3 × 3 = 2137 mm. Left: 2440 − 2137 = 303 mm, an offcut 560 × 303.

The full cut tree in order
CutWorks inDirection and lengthFrees
1SheetRip, 2440 mmStrip A, 2440 × 560
2Rest of sheetRip, 2440 mmStrip B, 2440 × 560, and offcut 2440 × 94
1.1Strip ACrosscut, 560 mmPart 720 × 560
1.2Strip ACrosscut, 560 mmPart 720 × 560
1.3Strip ACrosscut, 560 mmPart 720 × 560 and offcut 560 × 271
2.1Strip BCrosscut, 560 mmPart 764 × 560
2.2Strip BCrosscut, 560 mmPart 764 × 560
2.3Strip BCrosscut, 560 mmPart 600 × 560 and offcut 560 × 303

Cuts 1.1 to 1.3 depend only on cut 1, so you could finish strip A before making cut 2. Either order is valid. Making both rips first keeps the long cuts together while the sheet is in one piece.

How do I check the tree adds up?

Two checks catch most mistakes. First, every length along a strip must add up: parts, plus one kerf per cut, plus the offcut, equals the strip length. Second, the areas must add up: parts, offcuts and kerf strips together equal the sheet.

Worked example: area check

Sheet: 2440 × 1220 = 2,976,800 mm², or 2.9768 m².

Parts: 3 × 720 × 560 + 2 × 764 × 560 + 600 × 560 = 2,401,280 mm² (2.4013 m²).

Offcuts: 2440 × 94 + 560 × 271 + 560 × 303 = 550,800 mm² (0.5508 m²).

Kerf: two rips of 2440 mm and six crosscuts of 560 mm, all 3 mm wide: (2 × 2440 + 6 × 560) × 3 = 24,720 mm².

Total: 2,401,280 + 550,800 + 24,720 = 2,976,800 mm². It matches the sheet.

Parts use about 80.7% of this sheet's area (2,401,280 ÷ 2,976,800). That figure is for this example only.

In what order should I make cuts inside one strip?

Inside a strip, all the crosscuts are children of the same rip, so the tree does not fix their order. Choose an order that keeps the piece you are cutting a sensible size and keeps track of the labels. A common habit is to work from one end of the strip to the other, freeing one part per cut, so the strip shortens by one part and one kerf each time and the offcut comes off last.

Worked example: strip A shortening as you go

Start: 2440 mm. After cut 1.1: 2440 − 720 − 3 = 1717 mm left.

After cut 1.2: 1717 − 720 − 3 = 994 mm left.

After cut 1.3: 994 − 720 − 3 = 271 mm left, which is the offcut.

Writing the remaining length after each cut, as above, is a quick check while you work. If the piece on the bench is not the length you wrote, stop and find out why before the next cut. The difference is usually a kerf that is wider than the one you entered, or a cut made on the wrong side of the line.

Board plans follow the same idea in one dimension. Each board is a strip, every cut is a crosscut, and the plan in the linear planner lists the parts end to end with the leftover length last.

What goes wrong with cut order?

  • A child cut planned before its parent, which would need a cut that stops partway across a piece.
  • Numbers that do not show the parent, so cuts get made in the wrong strip.
  • Pieces not labelled as they come off, so two parts of similar size get swapped.
  • Kerf left out of a strip's arithmetic, so the last part in the strip is short.
  • Small trims made first, leaving a heavy, awkward piece for the long cuts.

Before cutting, read the diagram as described in how to read a cutting diagram, and check the placed and unplaced counts in the sheet planner. Kerflio plans geometry and order only. For how to make each cut with your tool, follow your saw's manual.

Frequently asked questions

Do I always rip a sheet before crosscutting?

No. Follow the cut tree of your layout. Many cabinet layouts start with rips because parts share widths, but a layout grouped by length starts with crosscuts.

Can I change the order of cuts in different strips?

Yes. Cuts in different branches do not depend on each other, so you can finish one strip before cutting the next free. A cut must still come after its own parent.

What numbering should I use for cuts?

Any scheme that shows each cut's parent works. Numbers such as 1, 1.1, 1.2 and 2, 2.1 make the parent obvious from the number.

Does Kerflio show the cut order?

Yes. The cut walkthrough follows the guillotine layout and lists parent cuts before the cuts inside them. It is a geometry order, not instructions for operating a saw.

How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.