What is on a cutting diagram?

A cutting diagram shows one stock item at a time: a sheet drawn as a rectangle, or a board drawn as a long bar. Inside it are the parts, each drawn to scale in the place it will be cut from. The gaps between parts are the kerf, and the leftover areas are offcuts. Most diagrams also carry a header with the stock size and a summary of how many parts were requested, placed and left unplaced.

Elements of a typical cutting diagram
ElementWhat it tells youWhat to check
Stock outline and sizeThe sheet or board the parts come fromIt matches the stock you measured, not just the label size
Part rectangle and labelWhich part goes whereThe label matches a row in your cut list
DimensionsThe part's length × widthSame unit as your list, length and width the right way round
Kerf gapMaterial the blade removesIt matches the kerf you entered
Offcut areaLeftover after all cutsWhether it is worth keeping
Grain arrowWhich way the face grain must runLocked parts are not turned
Placed and unplaced countsWhether every requested part fitsUnplaced is zero before you cut

How do I read the labels and dimensions?

Each part carries a label, such as Side or S1, and its size. Find the label in your cut list and check the size against the row. Read the size as length × width, in the unit written next to the numbers. A part drawn as 760 × 380 has its 760 mm edge running along the direction shown in the drawing. If the part is turned, the 760 edge may run across the sheet instead, which matters for grain.

Copies of the same part usually share a label, sometimes with a number added (Shelf 1, Shelf 2). Count them on the diagram. If your list asks for four shelves and you can find three, the fourth is either on another sheet or unplaced. If you work in inches and fractions, check the diagram shows the same unit you entered. See fractions, inches and millimetres.

What are the thin strips between parts?

The narrow gaps between parts are the kerf: the width of material the blade turns to dust. A layout that leaves no gap between two parts that need a cut between them is wrong for a real saw. The gap must match your measured kerf, which you enter once for the job. How to measure your saw kerf shows how.

At a 3 mm kerf the gaps can be hard to see on a small screen or a printed page. You can check them with arithmetic instead: along any strip, the parts plus one kerf per cut plus the offcut must equal the strip length. Saw kerf explained works through the sum.

How do I spot offcut areas?

Offcuts are the areas of stock that hold no part. They appear at the end of a strip, along an edge, or as a whole unused region. Some planners shade or hatch them. Read their sizes, because some will be worth keeping and some will be scrap. Decide with a written rule, as described in what offcuts to keep.

Remember that a drawn offcut is planned, not real. Its true size is known only after the cuts, so measure it before you label and store it.

What do grain arrows mean?

A grain arrow on a part shows which way the face grain must run in the finished piece. A matching arrow or note on the sheet shows which way its grain runs. For a grain-locked part, the two arrows must point the same way. If a planner allows rotation for a part, that part can be drawn turned a quarter turn, and its arrow (if any) turns with it.

Check grain on every visible part before you mark the sheet. A part placed sideways by mistake can look fine on screen and be wrong in the finished cabinet. Kerflio honours no-rotate per part, so a part you marked as grain-locked will not be turned. More in grain and rotation and plywood grain direction for cabinets.

What do placed and unplaced counts mean?

Requested is the number of parts on your list. Placed is the number drawn on the diagrams. Unplaced is the number the planner could not fit into the stock you gave it. Requested always equals placed plus unplaced. Kerflio shows all three and does not drop a part silently.

requested = placed + unplacedunplaced must be 0 before you cut

If unplaced is above zero, add stock, change a part size or allow rotation where grain does not matter, then plan again. Do not start cutting on a plan with unplaced parts and hope to find room later. The planner searches for a good guillotine layout but does not promise the best possible one, so a second try with more stock may place everything. See the methodology.

Worked example: reading one sheet diagram

Here is a diagram described in words, so you can follow it without a picture. Stock: one 2440 × 1220 mm sheet of 18 mm plywood, grain along the 2440 mm length. Kerf 3 mm (an assumed value for this example).

Source: NBS Source: Hanson birch plywood product listing, checked 2026-11-14. It lists 2440 × 1220 mm and 3050 × 1525 mm sheets. Sizes vary by product and supplier, so measure the sheet you buy.

Cut list for the example
LabelSize (mm)QtyRotation
Side900 × 4002No, grain along 900
Top600 × 4001No, grain along 600
Shelf760 × 3804Allowed
Back1200 × 8001No, grain along 1200

The diagram shows three horizontal strips, read from the bottom edge up:

  • Strip 1, 400 mm high: Side, Side, Top, left to right. Along the strip: 900 + 3 + 900 + 3 + 600 + 3 = 2409 mm, leaving a 31 × 400 offcut at the right end.
  • Above strip 1, after its rip: 1220 − 400 − 3 = 817 mm of sheet remain.
  • Strip 2, 380 mm high: Shelf, Shelf, Shelf. Along the strip: 3 × (760 + 3) = 2289 mm, leaving a 151 × 380 offcut.
  • After that rip: 817 − 380 − 3 = 434 mm remain, as strip 3.
  • Strip 3, 434 mm high: one Shelf at the left in a 760 × 434 piece, with a 51 mm strip above it (434 − 380 − 3 = 51). The rest of the strip is an offcut, 2440 − 760 − 3 = 1677 mm long by 434 mm.

Header: requested 8, placed 7, unplaced 1. The unplaced part is the Back, 1200 × 800 mm with grain locked along 1200. No region left on the sheet is 800 mm wide, so it cannot fit here.

Reading this diagram tells you three things before any cut: the sides and top are grain-correct, the large 1677 × 434 offcut is worth keeping, and you need a second sheet or a different back panel material before you start.

How do I read a plan with several sheets?

When a job needs more than one sheet or board, the planner draws each one separately, usually numbered Sheet 1, Sheet 2 and so on. Each drawing has its own stock size, parts and offcuts. Read them one at a time and mark the stock with the same number before you cut, so a part meant for Sheet 2 is not cut from Sheet 1.

The placed and unplaced counts cover the whole job, not one sheet. Add up the parts you can see on all the drawings: that total should equal placed. If you entered offcuts as well as full sheets, check which drawings use offcuts, because those pieces need to be fetched from the rack before you start.

What should I check before cutting from a diagram?

  • Stock size on the diagram matches the measured sheet or board.
  • Every label matches a cut list row, and the count of each label is right.
  • Units and length × width order match your list.
  • Kerf matches your measured value.
  • Grain arrows on locked parts follow the sheet's grain.
  • Unplaced is zero.
  • You know which offcuts you will keep.
  • You have the cut order. See cutting order for sheet goods.

For board diagrams in the linear planner the same checks apply, with lengths instead of rectangles: each board shows its parts end to end, a kerf between them and the remaining length at the end.

Frequently asked questions

Why is a part missing from my cutting diagram?

It may be on another sheet, or unplaced because it did not fit the stock you entered. Check the unplaced count, then add stock or change the part before you cut.

Are the gaps between parts on the diagram waste?

Yes. They are the kerf, the material the blade removes. They must match the kerf you measured.

Is a drawn offcut the size I will get?

It is the planned size. Measure the real piece after cutting, because extra trims or damage can make it smaller.

Can I print a Kerflio diagram?

The Android app shares a readable PDF plan. The free web planners show the diagram in your browser.

How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.