Which way should the grain run on each cabinet part?

There is no law here. What follows is the common convention for veneered plywood casework, where the grain follows the longest edge you see from the front. Your design can break it on purpose, for example with horizontal grain on all doors in a modern kitchen.

Common grain direction by cabinet part
PartUsual grain directionWhy
Sides (gables)Vertical, along the heightMatches the face frame or door grain beside it, and the long edge is vertical
Top and bottomSide to side, along the widthThe front edge shows long grain, which takes banding or edging cleanly
Fixed and adjustable shelvesSide to side, along the lengthThe front edge shows long grain, and the face veneers run along the span
DoorsVerticalMatches the sides. A row of doors reads as one surface
Drawer frontsHorizontal is common. Vertical when the fronts are cut in sequence to continue the grain up a stackDesign choice. Decide before cutting
BacksVerticalMatches the sides when the back is visible inside open shelving
Drawer boxesAlong the length of each side, front and backThe top edge shows long grain
Toe kick and railsAlong the lengthLong, narrow parts are stronger and cleaner with the grain along them

The plywood note on shelves is about the outer veneers. Plywood alternates the grain of each layer, so it is far less directional than solid wood, but the face veneers still run one way. The Canadian Plywood Association says expansion in balanced plywood is "slightly greater along the grain but much less across the grain than for solid wood", and that the cross bands make the change roughly the same per unit length in both directions.

Source: Canadian Plywood Association, Plywood Design Fundamentals, checked 2026-11-14.

Which direction is the grain on the sheet?

On a standard sheet the face grain usually runs along the long side. WISA states that the first dimension in its size list runs parallel to the face grain, which is why it lists sizes such as 2500 × 1250 mm for spruce. Some specialty panels are made with the grain across the short side, so look at the sheet before you plan.

Source: WISA sizes, thicknesses and weights, checked 2026-11-14.

In Kerflio, the long side of a sheet is its length. Enter the part's grain dimension as its length too, so "length" means "along the grain" for every row. Grain and rotation explains how the planner reads that setting. This page is about choosing the direction in the first place.

How do grain choices become no-rotate parts?

Write every part so its first dimension follows the grain. Then you only need one flag.

  1. For a side 720 mm tall and 560 mm deep with vertical grain, enter length 720, width 560.
  2. For a shelf 564 mm wide and 300 mm deep with grain side to side, enter length 564, width 300.
  3. For a drawer front 596 mm wide and 180 mm tall with horizontal grain, enter length 596, width 180.
  4. Turn rotation off for every row where the face shows. Leave it on for hidden parts, such as a drawer bottom that only you will ever see.

With that habit, a cut list reads the same in your notes, in the sheet planner and in a CSV file. The CSV format guide lists the grain and can_rotate columns.

Does locking grain cost extra sheets?

Sometimes, but often less than people expect. Run the numbers before you give up on grain. Here are two parts from a base cabinet on a 2440 × 1220 mm sheet with the grain along 2440, a 3 mm kerf and a simple grid.

Worked example: cabinet sides, 720 × 560 mm, grain along 720

Grain-correct: 3 along the length (3 × 720 + 2 × 3 = 2166 mm) and 2 across (2 × 560 + 3 = 1123 mm), so 6 sides.

Rotated: 4 along the length (4 × 560 + 3 × 3 = 2249 mm) but only 1 across (two would need 2 × 720 + 3 = 1443 mm), so 4 sides.

Here the grain-correct layout is also the better one.

Worked example: shelves, 564 × 300 mm, grain along 564

Grain-correct: 4 along the length (4 × 564 + 3 × 3 = 2265 mm) and 4 across (4 × 300 + 3 × 3 = 1209 mm), so 16 shelves.

Rotated: 8 along the length (8 × 300 + 7 × 3 = 2421 mm) and 2 across (2 × 564 + 3 = 1131 mm), also 16.

Same count, but the rotated shelves have the grain running front to back.

When a no-rotate rule does cost a sheet, it is usually on mixed lists where one awkward part is left over. Kerflio shows unplaced parts separately, so you can see which one. You can then cut that part from a second, smaller sheet, or accept a hidden part with the grain turned.

How do I match grain across doors and drawer fronts?

Grain matching is a visual decision that a cut list optimizer does not make for you. Kerflio keeps a part's orientation, but it does not keep neighbouring parts in sequence on the sheet. Plan matched parts by hand.

  • For a bank of drawer fronts with continuous vertical grain, draw one tall blank on the sheet, the full height of the stack plus the kerfs between fronts. Cut it out, mark the order, then crosscut the fronts.
  • For a pair of doors, cut them side by side from one blank so the grain runs across the meeting line.
  • In the planner, enter the blank as a single part. That way the layout keeps the area together.
  • Roseburg lists veneer matching options for hardwood plywood faces such as slip, book and whole piece. A whole-piece face suits matched doors better than a face made of narrow leaves, so ask what your sheet has.

Source: Roseburg hardwood plywood technical data sheet, checked 2026-11-14.

Worked example: one blank for three drawer fronts

Fronts 180, 180 and 240 mm tall, 596 mm wide, two kerfs of 3 mm between them.

Blank height: 180 + 180 + 240 + 3 + 3 = 606 mm.

Enter one part 606 × 596 mm with grain along 606 (vertical) and rotation off.

What about the back panel and hidden parts?

A 6 mm back inside a closed cabinet is rarely seen, so let it rotate. The same goes for drawer bottoms, cleats and stretchers hidden behind a face frame. Every part you free up gives the layout search more room. Keep rotation off for any part that shows in open shelving, a glass-door cabinet or the inside of a wardrobe you will look into every day.

Example: a base cabinet cut list with grain notes

Here is one base cabinet written with "length along the grain" for every row. The sizes are an example, not a standard cabinet.

Base cabinet parts, 18 mm plywood, length along the grain
PartQtyLength × width (mm)Grain on the cabinetRotate
Side2720 × 560VerticalNo
Bottom1564 × 560Side to sideNo
Shelf1564 × 300Side to sideNo
Top rail2564 × 100Side to sideYes if hidden
Door2716 × 296VerticalNo

Notice that the door is written 716 × 296, not 296 × 716. The first number is always the grain direction. That habit is what makes the rotation flag mean the same thing on every row.

Does MDF or melamine need a grain setting?

Raw MDF and particleboard have no grain, so rotation is fine. Decor boards are different. A melamine or foil board printed with wood grain has a pattern direction, and edging is often made to match it. Treat those boards like veneered plywood. MDF vs plywood for cabinets covers how the board choice changes the cut list.

Common grain mistakes

  • Writing width first for some parts and length first for others. Pick "length along the grain" and keep it.
  • Leaving rotation on for doors because the plan "looked better".
  • Cutting matched drawer fronts as separate parts and losing the order.
  • Assuming the grain runs along the long side of a specialty sheet without looking.
  • Locking every hidden part and then buying an extra sheet.

For the cutting sequence on a full sheet, see guillotine cuts explained.

Frequently asked questions

Should plywood grain run vertically on cabinet sides?

That is the usual choice, because it matches the doors and the long edge is vertical. It is a design convention, so a horizontal-grain kitchen can do the opposite on purpose.

Which way should the grain run on a plywood shelf?

Usually side to side, along the shelf's length. The front edge then shows long grain, and the face veneers run along the span.

Does a cut list optimizer match grain between parts?

Kerflio keeps each part's orientation when rotation is off, but it does not keep parts next to each other in sequence. Plan matched fronts as one blank and cut it apart later.

Do I need to lock grain on hidden parts?

Usually not. Letting hidden parts rotate gives the layout more options and can save material.

How do I know which way the grain runs on my sheet?

Look at the face. On standard sheets it usually runs along the long side, and WISA lists the dimension parallel to the face grain first.

How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.