What are the design assumptions?

Every size in a cabinet cut list follows from a few decisions made before any arithmetic. Change one and several parts change with it. This is an example design, chosen to show the method, so treat the numbers as a model to adapt.

  • Frameless (European style) box: the door covers the front edges of the sides, so there is no face frame.
  • Sides run to the floor, with the toe kick notched out of the front bottom corner after cutting. The cut list records the full rectangle.
  • The bottom panel sits between the sides. The top is two rails 100 mm (4 in) wide, also between the sides, because the worktop covers the box.
  • Two kick rails sit under the bottom, one at the toe kick face and one at the back.
  • The back is a thin panel nailed and glued onto the rear edges of the sides, bottom and rear top rail. Its thickness therefore adds to the overall depth.
  • One adjustable shelf on shelf pins and one full overlay door.
Example overall sizes
DimensionMetric versionImperial version
Width600 mm24 in
Box height, floor to top of sides870 mm34-1/2 in
Depth including back560 mm23-1/2 in
Toe kick, height × depth100 × 50 mm4 × 3 in
Example worktop thickness30 mm1-1/2 in
Counter height with worktop900 mm36 in
Carcass panel, measured18 mm23/32 in (sold as 3/4 in)
Back panel, measured6 mm1/4 in

The imperial version lands at 36 in to the worktop surface because the NKBA kitchen planning guidelines use 36 in (914 mm) high counters in their seating guideline and describe a preparation counter 24 in (610 mm) deep. The metric version lands at 900 mm, a little lower. These are planning guidelines, so check your worktop, appliances and local practice before you fix a height.

Source: NKBA Kitchen Planning Guidelines with Access Standards (PDF), checked 2026-11-14. Guideline 9 (seating clearance) and Guideline 12 (preparation area).

What thickness is 18 mm or 3/4 in plywood really?

Measure it with calipers before you work out a single part, because the interior width depends on it twice. In North America, a panel sold as 3/4 in is often thinner. The APA sanded plywood guide lists both 23/32 and 3/4 as Performance Categories, and APA says the Performance Category serves as the nominal panel thickness, so the label tells you the category and the calipers tell you the size.

Source: APA Sanded Plywood brochure, Guide to APA Sanded Plywood Grades (PDF), checked 2026-11-14.

Source: APA, Plywood, checked 2026-11-14.

Worked example: the same cabinet in two thicknesses

Interior width with panels measuring 3/4 in: 24 − 3/4 − 3/4 = 22-1/2 in.

Interior width with panels measuring 23/32 in: 24 − 23/32 − 23/32 = 22-9/16 in.

The difference is 1/16 in on every part that sits between the sides. Cut the bottom and rails to 22-1/2 in and the box is 1/16 in narrower than drawn, which pulls the doors out of line.

Metric sheets are sold by nominal thickness too. An example UK retail listing describes birch plywood as 2440 × 1220 × 18 mm. Your sheet may measure a little over or under 18 mm, so put the measured figure into the arithmetic below.

Source: MKM, Birch Faced Plywood 2440mm x 1220mm x 18mm (example retail listing), checked 2026-11-14.

How is each part size worked out?

Work from the outside dimensions inwards. Any part that sits between two others loses their thickness. Any part that sits in front of the back loses the back's thickness.

Sides

Side depth = overall depth − back thickness = 560 − 6554 mm
Imperial: 23-1/2 − 1/423-1/4 in

Side height is the box height: 870 mm (34-1/2 in). The toe kick notch, 100 × 50 mm (4 × 3 in), is cut from each side after the side is cut to size.

Bottom, top rails and kick rails

Length between sides = width − 2 × panel = 600 − 2 × 18564 mm
Imperial: 24 − 2 × 23/3222-9/16 in

The bottom is 564 × 554 mm (22-9/16 × 23-1/4 in), flush with the side edges front and back. The two top rails and the two kick rails are each 564 × 100 mm (22-9/16 × 4 in). The kick rail height equals the toe kick height, because the bottom panel rests on the kick rails.

Adjustable shelf

Shelf length = 564 − 2 × 1 mm clearance562 mm
Imperial: 22-9/16 − 2 × 1/3222-1/2 in

Shelf depth is set back from the front so the door and hinges clear it. This example uses 554 − 34 = 520 mm and 23-1/4 − 1-3/4 = 21-1/2 in. Check your hinge maker's drawings for the space the hinge needs.

Back

Back height = box height − toe kick = 870 − 100770 mm
Imperial: 34-1/2 − 430-1/2 in

The back covers the full width, 600 mm (24 in), from the top of the box down to the underside of the bottom panel. The rear kick rail sits below it.

Door

Door width = 600 − 2 × 2 mm gap596 mm
Door height = 870 − 100 − 3 mm top gap767 mm

Imperial, with 1/16 in side gaps and a 1/8 in top gap: 24 − 2 × 1/16 = 23-7/8 in wide and 34-1/2 − 4 − 1/8 = 30-3/8 in high. These gaps are example values. Size real doors from the overlay chart for your hinge and plate.

What is the complete cut list?

Metric version, millimetres, 18 mm plywood unless stated
PartQtyLength × widthMaterialGrain / rotate
Side (L and R)2870 × 55418 mm plywoodGrain along 870, do not rotate
Bottom1564 × 55418 mm plywoodRotate allowed
Top rail (front, rear)2564 × 10018 mm plywoodRotate allowed
Kick rail (front, rear)2564 × 10018 mm plywoodRotate allowed
Adjustable shelf1562 × 52018 mm plywoodRotate allowed
Door1767 × 59618 mm plywoodGrain along 767, do not rotate
Back1770 × 6006 mm panelRotate allowed
Imperial version, inches, 23/32 in plywood unless stated
PartQtyLength × widthMaterialGrain / rotate
Side (L and R)234-1/2 × 23-1/43/4 in nominal plywoodGrain along 34-1/2, do not rotate
Bottom122-9/16 × 23-1/43/4 in nominal plywoodRotate allowed
Top rail (front, rear)222-9/16 × 43/4 in nominal plywoodRotate allowed
Kick rail (front, rear)222-9/16 × 43/4 in nominal plywoodRotate allowed
Adjustable shelf122-1/2 × 21-1/23/4 in nominal plywoodRotate allowed
Door130-3/8 × 23-7/83/4 in nominal plywoodGrain along 30-3/8, do not rotate
Back130-1/2 × 241/4 in panelRotate allowed

That is nine pieces of carcass plywood and one back. If you band the front edges, subtract the band from the finished size first. The edge banding allowance guide shows how.

How many sheets does it take?

Start with area, then confirm with a layout, because area alone ignores the strips a layout leaves behind.

Worked example: area check, metric

Parts: 2 × 870 × 554 + 564 × 554 + 4 × 564 × 100 + 562 × 520 + 596 × 767 = 2,251,388 mm².

One sheet: 2,440 × 1,220 = 2,976,800 mm².

2,251,388 ÷ 2,976,800 = 75.6%, so one sheet is possible by area.

A hand layout in edge-to-edge strips, with an example 3 mm kerf:

  1. Rip a 554 mm strip along the sheet. Crosscut it into side, side and bottom: 870 + 3 + 870 + 3 + 564 = 2,310 mm, which is under 2,440.
  2. Rip a 596 mm strip. Crosscut the door (767), then the shelf (562): 767 + 3 + 562 = 1,332 mm. Crosscut a 564 mm block from what is left and rip it into four 100 mm rails: 4 × 100 + 3 × 3 = 409 mm, which is under 596.
  3. What remains across the sheet: 1,220 − 554 − 3 − 596 − 3 = 64 mm.

Imperial, with a 1/8 in kerf: the first strip needs 34-1/2 + 1/8 + 34-1/2 + 1/8 + 22-9/16 = 91-13/16 in of the 96 in length. The second strip, 23-7/8 in wide, holds the door and shelf in 30-3/8 + 1/8 + 22-1/2 = 53 in, and the four rails need 4 × 4 + 3 × 1/8 = 16-3/8 in of its width. Across the sheet, 48 − 23-1/4 − 1/8 − 23-7/8 − 1/8 = 5/8 in is left. If you need to trim a damaged factory edge, that 5/8 in is your whole margin.

Kerflio's planner placed all nine parts on one sheet in both versions, using 75.6% of the metric sheet and 80.3% of the imperial one. The kerf values here are examples. Measure your own kerf and use that figure.

The back comes from a separate thin sheet. Two 600 mm backs fit across a 1,220 mm sheet (600 + 3 + 600 = 1,203 mm) and three fit along it (770 + 3 + 770 + 3 + 770 = 2,316 mm), so one thin sheet covers several cabinets.

Which parts need their grain locked?

The sides and the door show their face grain, so this example locks them with the grain running vertically, along their long dimension. In a planner that means "do not rotate". The bottom, rails and shelf are inside the box or hidden, so they may turn a quarter turn to fit. That freedom is what lets the rails drop into an offcut.

A sheet's face grain usually runs along its long edge, but check yours. The grain direction for cabinets page and grain and rotation page go into the choices.

What mistakes cost a sheet or a redo?

  • Using the nominal thickness. A 3/4 in label on a 23/32 in panel makes every between-the-sides part 1/16 in short.
  • Forgetting the back. With an applied back, the side depth is the overall depth minus the back. With a grooved back, the arithmetic changes again (see the wall cabinet example).
  • Sizing the door from the box instead of from the hinge maker's overlay chart.
  • Cutting the toe kick notch into the cut list size. Cut the full rectangle first, then notch.
  • Leaving out the rails. Four 564 × 100 mm parts are easy to drop from a list written from memory.
  • Skipping the kerf. The layout above has a 64 mm (or 5/8 in) margin. Three extra kerfs you did not count would still fit, but a rough factory edge might not.
  • Planning each cabinet on its own sheet. A run of cabinets shares sheets better when planned together, as the kitchen cabinet cut list shows.

Can I plan this cabinet in Kerflio?

Yes. The carcass is nine pieces, within the 12-piece limit of the free sheet cut planner, which runs in your browser. Enter your measured thickness, your sheet size and your kerf, set the sides and door to no rotation, and check that placed plus unplaced equals nine. For drawers in this same box, continue with the drawer box cut list.

Frequently asked questions

Why is the bottom between the sides instead of under them?

It keeps the sides running to the floor, which carries the load straight down and hides the bottom edge. Some builders put the bottom under the sides instead; then the sides get shorter and the bottom gets wider, so rework every size.

Can I use a full top panel instead of two rails?

Yes. The top then becomes 564 × 554 mm (22-9/16 × 23-1/4 in) and the rail rows drop out. Check that it still fits on the sheet.

What if my back sits in a groove?

Then the sides run the full depth and the back is cut larger than the opening by the groove depth on each edge. The wall cabinet example works through that method.

Does the cut list include the worktop?

No. The worktop is usually bought or made separately. This list covers the carcass, back and door.

How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.