How do you size a box for side-mount slides?

Start from the clear opening between the cabinet sides, not from the drawer front. Each slide takes a fixed amount of space between the box and the cabinet side, so:

Box outside width = opening width − 2 × side spaceper slide maker

The side space comes from the slide maker. Accuride Europe says its 3832 slide is 12.7 mm thick and needs a side space between 12.9 and 13.2 mm. In inches that is 12.9 ÷ 25.4 = 0.508 in to 13.2 ÷ 25.4 = 0.520 in, so a little over 1/2 in. The page also gives a general rule of 0.2 to 0.5 mm over the slide thickness for most slides, and warns that some slides differ.

Source: Accuride Europe, Understanding side space, checked 2026-11-14.

Source: NIST Guide to the SI, Appendix B.8 conversion factors, checked 2026-11-14. One inch is exactly 0.0254 m (25.4 mm).

If you use a different slide, find its own data sheet. Do not carry the 3832 number across to another model.

What opening are we filling?

This page fills the base cabinet example with three drawers instead of a door and shelf. It is an example design. The opening is measured between the parts that the drawers live between.

Opening in the example base cabinet
DimensionMetricImperial
Width between sides564 mm22-9/16 in
Top of bottom panel above floor100 + 18 = 118 mm4 + 23/32 = 4-23/32 in
Underside of top rails above floor870 − 18 = 852 mm34-1/2 − 23/32 = 33-25/32 in
Clear height852 − 118 = 734 mm33-25/32 − 4-23/32 = 29-1/16 in
Clear depth (back applied behind)554 mm23-1/4 in

Measure the built cabinet before you cut boxes. A box that is 1 mm too wide will not go in; a box that is 1 mm too narrow may not engage the slides.

How wide is each box?

Worked example: box width, metric

Side space chosen: 13 mm per side, inside the 12.9 to 13.2 mm range.

Box outside width = 564 − 2 × 13 = 538 mm.

Worked example: box width, imperial

Exactly 1/2 in per side would be 12.7 mm, under the 12.9 mm minimum, so aim a hair wider.

Side space chosen: 33/64 in per side, which is 0.516 in or about 13.10 mm.

Box outside width = 22-9/16 − 2 × 33/64 = 21-17/32 in.

All three boxes share this width because they share the opening.

How tall is each box in a stack of three?

Split the clear height into three spaces, then make each box shorter than its space. The gap above each box gives room to hook it onto the slides and lift it out. This example leaves 30 mm (1-1/4 in) per drawer. Check your slide's installation sheet for its own mounting needs.

Worked example: box heights, metric

Boxes: 140, 252 and 252 mm.

Check: 140 + 252 + 252 + 3 × 30 = 734 mm, the clear height.

Worked example: box heights, imperial

Boxes: 5-1/2, 9-7/8 and 9-7/8 in.

Check: 5-1/2 + 9-7/8 + 9-7/8 + 3 × 1-1/4 = 29 in.

The opening is 29-1/16 in, so 1/16 in is spare. Add it to the top drawer gap.

The drawer fronts follow the door zone of the base cabinet, 767 mm (30-3/8 in) tall. With 3 mm gaps between fronts: 177 + 3 + 292 + 3 + 292 = 767 mm. Imperial, with 1/8 in gaps: 7 + 1/8 + 11-9/16 + 1/8 + 11-9/16 = 30-3/8 in. Fronts are 596 mm (23-7/8 in) wide, the same as the door they replace.

How long is each box, and what about the front, back and bottom?

Choose a slide length that fits the clear depth, then size the box to it. This example uses 500 mm slides in the 554 mm deep metric cabinet and 22 in slides in the 23-1/4 in deep imperial one, and makes the box length equal the nominal slide length. Check that your slide is made in that length and read the maker's minimum cabinet depth.

Box construction in this example: sides 12 mm (1/2 in nominal, measured) run the full length; the front and back sit between the sides; a 6 mm (1/4 in) bottom sits in a groove 6 mm (1/4 in) deep in all four parts.

Front and back length = 538 − 2 × 12514 mm
Imperial: 21-17/32 − 2 × 1/220-17/32 in
Worked example: bottom panel, metric

Inside width 514, plus 2 × 6 groove, minus 2 × 1 clearance = 524 mm.

Inside length 500 − 2 × 12 = 476, plus 2 × 6 groove, minus 2 × 1 clearance = 486 mm.

Worked example: bottom panel, imperial

Width: 20-17/32 + 2 × 1/4 − 2 × 1/32 = 20-31/32 in.

Length: 22 − 2 × 1/2 + 2 × 1/4 − 2 × 1/32 = 21-7/16 in.

If your drawer sides measure 11.5 mm or 15/32 in, redo the front and back length with that figure. A box built from thinner sides comes out narrower and loses slide engagement.

What is the complete cut list for the stack?

Metric version, millimetres
PartQtyLength × widthMaterialGrain / rotate
Drawer 1 side2500 × 14012 mm plywoodGrain along 500, do not rotate
Drawer 1 front and back2514 × 14012 mm plywoodGrain along 514, do not rotate
Drawer 2 and 3 side4500 × 25212 mm plywoodGrain along 500, do not rotate
Drawer 2 and 3 front and back4514 × 25212 mm plywoodGrain along 514, do not rotate
Bottom3524 × 4866 mm plywoodRotate allowed
Drawer front, top1596 × 17718 mm plywoodGrain along 596, do not rotate
Drawer front, lower2596 × 29218 mm plywoodGrain along 596, do not rotate
Imperial version, inches
PartQtyLength × widthMaterialGrain / rotate
Drawer 1 side222 × 5-1/21/2 in plywoodGrain along 22, do not rotate
Drawer 1 front and back220-17/32 × 5-1/21/2 in plywoodGrain along 20-17/32, do not rotate
Drawer 2 and 3 side422 × 9-7/81/2 in plywoodGrain along 22, do not rotate
Drawer 2 and 3 front and back420-17/32 × 9-7/81/2 in plywoodGrain along 20-17/32, do not rotate
Bottom321-7/16 × 20-31/321/4 in plywoodRotate allowed
Drawer front, top123-7/8 × 73/4 in nominal plywoodGrain along 23-7/8, do not rotate
Drawer front, lower223-7/8 × 11-9/163/4 in nominal plywoodGrain along 23-7/8, do not rotate

The grain choice here keeps the face grain running around the box. If your drawer material has no visible grain, let the parts rotate.

How much sheet does the stack use?

Rip one strip per box height and crosscut all four parts of that box from it. With an example 3 mm kerf, each strip needs 500 + 3 + 514 + 3 + 500 + 3 + 514 = 2,037 mm of the 2,440 mm length. The three strips take 140 + 3 + 252 + 3 + 252 = 650 mm of the 1,220 mm width, so the box parts use about half a sheet of 12 mm plywood.

Imperial, with a 1/8 in kerf: 22 + 20-17/32 + 22 + 20-17/32 + 3 × 1/8 = 85-7/16 in per strip, and 5-1/2 + 9-7/8 + 9-7/8 + 2 × 1/8 = 25-1/2 in across the 48 in sheet.

Kerflio's planner placed all twelve box parts on one sheet: 43.9% of a 2,440 × 1,220 mm sheet and 46.6% of a 48 × 96 in sheet. The three 6 mm bottoms used 25.7% of one thin sheet. That spare half sheet is worth planning: more drawers, or the parts of the next cabinet. See what offcuts to keep.

What changes for undermount slides?

Undermount slides use a different formula, set by each maker for each model. Do not use the side-mount arithmetic above.

As one example, Blum's TANDEM plus BLUMOTION 563H specification sheet says the inside drawer width must equal the opening width minus 42 mm (1-21/32 in). It lists a maximum drawer side thickness of 16 mm (5/8 in), a 13 mm (1/2 in) bottom recess and a maximum drawer height of the opening minus 21 mm (13/16 in). For 16 mm (5/8 in) sides it gives the outside drawer width as the opening minus 10 mm (13/32 in).

Source: Blum TANDEM plus BLUMOTION 563H specification sheet (Blum, Inc., PDF hosted by a retailer), checked 2026-11-14. Use the sheet for your exact model; other TANDEM and undermount lines use different numbers.

Worked example: the same 564 mm opening on 563H slides

Inside width = 564 − 42 = 522 mm.

Outside width with 16 mm sides = 522 + 2 × 16 = 554 mm, matching 564 − 10 = 554 mm from the table.

Imperial: inside 22-9/16 − 1-21/32 = 20-29/32 in; outside with 5/8 in sides 22-9/16 − 13/32 = 22-5/32 in.

Compare the side-mount box: 538 mm outside. The same opening gives two different boxes.

What mistakes ruin drawer boxes?

  • Sizing from the drawer front instead of the opening between the cabinet sides.
  • Rounding the side space down to exactly 1/2 in. For the 3832 that is below the stated minimum.
  • Using nominal drawer side thickness. The front and back length depends on the measured side.
  • Making the bottom the inside size. A grooved bottom is larger than the inside by the groove depth on each edge.
  • Forgetting the gap above each box when splitting the height.
  • Mixing slide types in one stack and using one formula for all of them.

Frequently asked questions

Is 1/2 in per side right for every side-mount slide?

No. It is close for slides that are 12.7 mm thick, and even then Accuride Europe asks for 12.9 to 13.2 mm for the 3832. Check the data sheet for the slide you bought.

Should the box be the same length as the slide?

In this example it is. Some makers allow a shorter box. Read the slide data sheet for the minimum cabinet depth and any rear clearance.

Can I plan the drawer parts in the free web planner?

Twelve box parts fit the 12-piece limit of the free sheet planner. The bottoms are a different material, so plan them as a second job.

Do the drawer fronts come from the same sheet as the boxes?

Not in this example. The fronts are 18 mm (3/4 in) carcass material and the boxes are 12 mm (1/2 in), so they are planned in different material groups.

How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.