What are the design assumptions?

This is an example design. It uses a different back method from the base cabinet example so the two pages together show both sets of arithmetic.

  • Frameless box. Sides run full height; top and bottom sit between the sides at full depth.
  • The back is a 6 mm (1/4 in) panel captured in a groove cut into the sides, top and bottom. The groove is 6 mm wide and 8 mm deep, set 10 mm in from the rear edge. Imperial: the groove matches the measured back thickness, is 1/4 in deep and sits 3/8 in from the rear edge.
  • A hanging rail 80 mm (3 in) wide sits under the top, in front of the back. Screws through it go into the wall. Use fixings suited to your wall and follow the fixing maker's instructions.
  • One fixed shelf at mid-height, glued and screwed or doweled between the sides. It ties the sides together and stops in front of the back.
  • One adjustable shelf on pins, set back so the door clears it.
  • One full overlay door with example gaps of 2 mm (1/16 in) all round.
Example overall sizes
DimensionMetric versionImperial version
Width600 mm24 in
Height720 mm30 in
Depth (sides)300 mm12 in
Carcass panel, measured18 mm23/32 in (sold as 3/4 in)
Back panel, measured6 mm1/4 in

The base cabinet page explains why you measure the panel instead of trusting the label. The same 23/32 in figure is used here.

How do the box parts work out?

The grooved back changes the depth arithmetic. The sides, top and bottom now run the full 300 mm (12 in), because the back sits inside them.

Interior width = 600 − 2 × 18564 mm
Imperial: 24 − 2 × 23/3222-9/16 in
Interior height = 720 − 2 × 18684 mm
Imperial: 30 − 2 × 23/3228-9/16 in

So the top and bottom are 564 × 300 mm (22-9/16 × 12 in) each. The sides are 720 × 300 mm (30 × 12 in). The hanging rail runs between the sides: 564 × 80 mm (22-9/16 × 3 in).

How big is a back that sits in a groove?

A captured back is bigger than the opening you see, because it reaches into the groove on all four edges. Take the interior size, add the groove depth twice, then take off a little clearance so the panel does not bottom out in the grooves.

Worked example: back panel, metric

Width: 564 + 2 × 8 groove − 2 × 1 clearance = 578 mm.

Height: 684 + 2 × 8 groove − 2 × 1 clearance = 698 mm.

Worked example: back panel, imperial

Width: 22-9/16 + 2 × 1/4 − 2 × 1/32 = 23 in.

Height: 28-9/16 + 2 × 1/4 − 2 × 1/32 = 29 in.

The groove must match the back's real thickness. Thin panels sold as 1/4 in or 6 mm vary, so measure the panel before you set the groove width. If you cut the groove first and the back is thicker, you either sand the back or recut the groove.

How deep are the fixed and adjustable shelves?

Both shelves sit in front of the back, so their depth starts from the front of the groove, not the rear edge of the side.

Fixed shelf depth = 300 − 10 setback − 6 groove width284 mm
Imperial: 12 − 3/8 − 1/411-3/8 in

The fixed shelf runs between the sides: 564 × 284 mm (22-9/16 × 11-3/8 in).

The adjustable shelf has to drop between the sides on its pins, so it gets clearance at each end. It is also set back from the front so the door and hinges clear it.

Adjustable shelf length = 564 − 2 × 1562 mm
Adjustable shelf depth = 284 − 14 setback270 mm

Imperial: 22-9/16 − 2 × 1/32 = 22-1/2 in long and 11-3/8 − 1/2 = 10-7/8 in deep. The 1 mm and 1/32 in clearances and the setbacks are example values. If you band the front edge, subtract the band from the depth; see the edge banding allowance.

Door

Door = (600 − 2 × 2) × (720 − 2 × 2)596 × 716 mm

Imperial: 24 − 2 × 1/16 = 23-7/8 in wide and 30 − 2 × 1/16 = 29-7/8 in high. Real door sizes come from your hinge maker's overlay chart.

What is the complete cut list?

Metric version, millimetres
PartQtyLength × widthMaterialGrain / rotate
Side (L and R)2720 × 30018 mm plywoodGrain along 720, do not rotate
Top and bottom2564 × 30018 mm plywoodRotate allowed
Fixed shelf1564 × 28418 mm plywoodRotate allowed
Adjustable shelf1562 × 27018 mm plywoodRotate allowed
Hanging rail1564 × 8018 mm plywoodRotate allowed
Door1716 × 59618 mm plywoodGrain along 716, do not rotate
Back1698 × 5786 mm panelRotate allowed
Imperial version, inches
PartQtyLength × widthMaterialGrain / rotate
Side (L and R)230 × 123/4 in nominal plywoodGrain along 30, do not rotate
Top and bottom222-9/16 × 123/4 in nominal plywoodRotate allowed
Fixed shelf122-9/16 × 11-3/83/4 in nominal plywoodRotate allowed
Adjustable shelf122-1/2 × 10-7/83/4 in nominal plywoodRotate allowed
Hanging rail122-9/16 × 33/4 in nominal plywoodRotate allowed
Door129-7/8 × 23-7/83/4 in nominal plywoodGrain along 29-7/8, do not rotate
Back129 × 231/4 in panelRotate allowed

How many sheets does one wall cabinet need?

Worked example: area check, metric

Parts: 2 × 720 × 300 + 2 × 564 × 300 + 564 × 284 + 562 × 270 + 564 × 80 + 596 × 716 = 1,554,172 mm².

That is 1,554,172 ÷ 2,976,800 = 52.2% of a 2,440 × 1,220 mm sheet.

Two cabinets would need 104.4% of a sheet, so two will not fit on one sheet whatever the layout.

A hand layout in strips, with an example 3 mm kerf:

  1. Rip a 300 mm strip. Crosscut side, side and top: 720 + 3 + 720 + 3 + 564 = 2,010 mm. About 427 mm of the strip is left.
  2. Rip a second 300 mm strip. Crosscut the bottom, the fixed shelf (284 wide, so 16 mm is trimmed off its edge) and the adjustable shelf: 564 + 3 + 564 + 3 + 562 = 1,696 mm.
  3. Rip a 596 mm strip. Crosscut the door and the hanging rail block: 716 + 3 + 564 = 1,283 mm.
  4. Width used across the sheet: 300 + 3 + 300 + 3 + 596 = 1,202 mm of 1,220.

Kerflio's planner also placed all eight carcass parts on one sheet: 52.2% of the metric sheet and 55.2% of a 48 × 96 in sheet in the imperial version. Its largest metric leftover was about 1,717 × 653 mm, big enough to matter. That is why a kitchen run should be planned as one job, which the kitchen cabinet cut list does.

What mistakes are common on wall cabinets?

  • Cutting the back to the visible opening. A grooved back must be larger than the opening by the groove depth on each edge, minus clearance.
  • Measuring shelf depth from the rear edge. With a grooved back, the shelf stops at the front face of the groove.
  • Cutting the adjustable shelf the same length as the fixed shelf. It needs end clearance or it will bind on the pins.
  • Locking every part against rotation. Only the visible-grain parts need it; the rest should be free so the planner can fit them into leftovers.
  • Grooving the top and bottom on the wrong face. Mark the inside face and rear edge of every part before you cut joinery.
  • Assuming a base cabinet depth. Wall cabinets in this example are 300 mm (12 in) deep, so the rails and shelves are different parts from the base page, even where the lengths match.

Can I plan it in Kerflio?

Yes. Eight carcass pieces fit within the 12-piece limit of the free sheet planner. Mark the sides and door as no-rotate, enter your measured thickness and kerf, and compare the leftover it reports with the parts of your next cabinet. The grain and rotation guide explains the rotation setting.

Frequently asked questions

Why put the back in a groove instead of nailing it on?

A captured back keeps the back edges of the sides clean and the outside dimensions exact. It costs a groove in four parts and a slightly fussier back size.

Can I make both shelves adjustable?

Yes. Use the adjustable shelf size for both. The fixed shelf in this example also ties the sides together, so if you remove it, think about how the box stays square.

Does the hanging rail go in front of or behind the back?

In this example it sits in front of the back, inside the box, so its length is the interior width. Some designs notch it into the sides behind the back instead, which changes its length and the back size.

Can I use the base cabinet shelf size here?

No. The depth is different and the back method changes where the shelf stops.

How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.