What are the design assumptions?

This is an example design, sized to show the cut list method. Choose the height and footprint that suit you and your space; the arithmetic is the same.

  • Top: one layer of 3/4 in nominal plywood (measured 23/32 in), 72 × 30 in. Metric: 18 mm plywood, 1800 × 750 mm.
  • Frame: four legs and two rectangles of rails, one under the top and one lower down for the shelf. The long rails run the full frame length on the outside of the legs; the short rails fit between the long rails.
  • Frame outside size: 68 × 26 in (1700 × 650 mm), so the top overhangs 2 in (50 mm) on every edge.
  • Height to the work surface: 34 in (860 mm), an example.
  • The legs stand with their 3-1/2 in (89 mm) face along the bench length.
  • Lower shelf: plywood resting on the lower rails, notched around the legs.

What size is a 2×4 really?

A 2×4 is a nominal name. The Southern Pine Inspection Bureau gives its dry dressed size as 1-1/2 × 3-1/2 in and points to the PS 20 American Softwood Lumber Standard for nominal and minimum dressed sizes.

Source: Southern Pine Inspection Bureau, Nominal vs actual lumber sizes, checked 2026-11-14.

In metric, 1-1/2 in × 25.4 = 38.1 mm and 3-1/2 in × 25.4 = 88.9 mm. Merchants in metric countries sell this section as 38 × 89 mm; an example UK listing describes 38mm x 89mm CLS at 2.44 m long.

Source: NIST Guide to the SI, Appendix B.8 conversion factors, checked 2026-11-14.

Source: MKM, 38mm x 89mm CLS, 2.44m (example retail listing), checked 2026-11-14.

Board lengths vary by merchant and region. This page uses 96 in (8 ft) and 2,440 mm boards. Measure yours, and use the usable length after any split or damaged end is cut off. See nominal versus actual lumber sizes and standard lumber lengths.

How is each frame part sized?

Legs

Leg = work height − top thickness = 34 − 23/3233-9/32 in
Metric: 860 − 18842 mm

The rails are fixed to the legs with their top edges flush with the leg tops, so the legs carry the top directly.

Rails

Long rail = frame length68 in (1700 mm)
Short rail = frame width − 2 × rail thickness = 26 − 2 × 1-1/223 in
Metric: 650 − 2 × 38574 mm

Each rectangle has two long and two short rails, and there are two rectangles: four of each.

Shelf

The shelf sits on the lower rails and covers the full frame: 68 × 26 in (1700 × 650 mm). Each corner is notched to clear a leg. From the outside corner, the notch spans the short rail plus the leg along the length, 1-1/2 + 3-1/2 = 5 in (38 + 89 = 127 mm), and the long rail plus the leg across, 1-1/2 + 1-1/2 = 3 in (38 + 38 = 76 mm). Cut the rectangle first, then the notches.

What is the complete cut list?

Frame, linear parts
PartQtyImperial lengthMetric lengthMaterial
Leg433-9/32 in842 mm2×4 (38 × 89 mm)
Long rail468 in1700 mm2×4 (38 × 89 mm)
Short rail423 in574 mm2×4 (38 × 89 mm)
Top and shelf, sheet parts
PartQtyLength × widthMaterialGrain / rotate
Top172 × 30 in (1800 × 750 mm)3/4 in nominal (18 mm) plywoodRotate allowed
Shelf, notched after cutting168 × 26 in (1700 × 650 mm)3/4 in nominal (18 mm) plywoodRotate allowed

Grain does not matter much on a shop top, so both parts may rotate. Lock it if you want the face grain running along the bench.

How many boards does the frame need, counting kerf?

Worked example: total length first, imperial

Parts: 4 × 33-9/32 + 4 × 68 + 4 × 23 = 497-1/8 in.

497-1/8 ÷ 96 = 5.18 boards, so at least 6.

Then fit parts board by board, with an example 1/8 in kerf between neighbouring parts. A cut is not needed where a part ends at the board end.

  • One long rail and one short rail: 68 + 1/8 + 23 = 91-1/8 in. Four boards like this give all four long rails and all four short rails.
  • Two legs: 33-9/32 + 1/8 + 33-9/32 = 66-11/16 in. Two boards like this give the four legs.
  • A long rail and a leg will not share a board: 68 + 1/8 + 33-9/32 = 101-13/32 in, longer than 96.

Six boards. Kerflio's linear planner gave the same plan: 12 of 12 pieces on six 96 in boards, 86.3% of the length used. After the cut that separates the offcut, the long-and-short boards leave about 4-3/4 in each and the leg boards about 29-3/16 in each.

Worked example: metric version, 2,440 mm boards, 3 mm kerf

Total: 4 × 842 + 4 × 1700 + 4 × 574 = 12,464 mm. 12,464 ÷ 2,440 = 5.11, so at least 6.

Long rail and short rail: 1700 + 3 + 574 = 2,277 mm. Leaves 160 mm after the separating cut.

Two legs: 842 + 3 + 842 = 1,687 mm. Leaves 750 mm.

The planner used six boards, 85.1% of the length.

The two leg-board offcuts are the useful ones. At 29-3/16 in they are long enough for a short rail each, so if you add a centre brace or a second shelf rail later, cut it from there. The kerf values are examples; measure your own.

How many plywood sheets do the top and shelf need?

The top fills 72 × 30 in of a 48 × 96 in sheet. The shelf is 68 × 26 in. Side by side across the sheet they need 30 + 1/8 + 26 = 56-1/8 in, more than 48. End to end along it they need 72 + 1/8 + 68 = 140-1/8 in, more than 96. So two sheets, and Kerflio's planner agreed: one part per sheet, 42.6% of the two sheets used.

After the top is cut, the first sheet still has a strip 48 − 30 − 1/8 = 17-7/8 in wide and 96 in long. If the shelf is no deeper than that, it fits the strip and the whole bench comes from one sheet. A shelf 17-7/8 in deep needs the lower short rails moved or the shelf supported on cleats, so decide that before cutting.

Worked example: metric version

Top 1800 × 750 and shelf 1700 × 650: 750 + 3 + 650 = 1,403 mm, more than 1,220. Two sheets.

Strip left beside the top: 1,220 − 750 − 3 = 467 mm wide and 1,800 mm long. A shelf up to 467 mm deep fits there.

How do you mark out the boards before cutting?

Mark every part on a board before you cut any of them. That way a split end or a knot shows up while you can still move the pattern. Follow your saw's manual for the cutting itself; the planning steps are these:

  1. Measure each board's usable length and set aside any with twist or bow for the legs, which are short enough to cut around a defect.
  2. Write the pattern for each board on its face: "long + short" on four boards, "leg + leg" on two.
  3. Mark from one end, then add the kerf on the waste side of each line. On a long-and-short board, the long rail mark is at 68 in, the blade takes the next 1/8 in, and the short rail starts at 68-1/8 in.
  4. Label each part as it comes off: L1 to L4 for legs, LR for long rails, SR for short rails, with "upper" or "lower" once you assemble.
  5. Keep the two 29-3/16 in leg-board offcuts together until the bench is finished.

If your measured boards are longer than 96 in, enter the real length in the planner. It may not save a board on this frame, but it does make the offcut figures true.

What mistakes are common with a lumber frame?

  • Cutting to the nominal size. A short rail of 26 − 2 × 2 = 22 in leaves the frame 1 in too narrow.
  • Forgetting the top thickness when cutting legs. The work height ends up 23/32 in (18 mm) too tall.
  • Counting kerf once per board instead of once per cut between parts.
  • Planning on the label length. If a board's end is split, the usable length is shorter, and a 91-1/8 in pattern on a 96 in board still has room, but a tighter one may not.
  • Picking boards with twist or bow for the long rails. Sort the straightest boards for rails and use the rest for legs.
  • Cutting the shelf to fit inside the legs after the frame is built, instead of cutting the rectangle first and notching.

Can I plan this in Kerflio?

Yes. The frame is exactly 12 pieces, the limit of the free linear cut planner. Enter your measured board length and kerf. The top and shelf go in the sheet planner as a separate job. The sheet versus linear guide explains why they are planned apart.

Frequently asked questions

What height should a workbench be?

It depends on you and the work. This page uses 34 in (860 mm) as an example; change the leg length to suit and the rest of the cut list stays the same.

Can I use a double-layer top?

Yes. Add a second 72 × 30 in top to the sheet list and take its thickness off the leg length too.

Should I buy 10 ft or 3 m boards instead?

Check with a plan first. Longer boards can pair parts that do not pair on 8 ft boards, but only the plan shows whether that saves a board.

Can MDF replace the plywood top?

It can for the cut list. It is a different material, so plan it as its own group and measure its thickness for the leg length.

How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.