What are the design assumptions?
This is an example design to show the planning, not a load-rated shelf. For heavy storage, follow a tested plan and fix tall units to the wall with fixings suited to your wall, following the fixing maker's instructions.
- Four plywood shelves, 3/4 in nominal (measured 23/32 in), or 18 mm in the metric version.
- Two ladder ends. Each has a front and a back post, 72 in (1800 mm) tall, joined by four horizontal cleats screwed to the inside faces of the posts.
- The shelves rest on the cleats and fit between the posts.
- Under each shelf, a front rail and a back rail run between the cleats and are screwed up into the shelf.
- The posts stand with their 1-1/2 in (38 mm) face across the width and their 3-1/2 in (89 mm) face along the depth.
- 2×4 actual size 1-1/2 × 3-1/2 in; metric 38 × 89 mm. Board length 96 in or 2,440 mm.
Source: Southern Pine Inspection Bureau, Nominal vs actual lumber sizes, checked 2026-11-14.
Source: MKM, 38mm x 89mm CLS, 2.44m (example retail listing), checked 2026-11-14.
Why not cut shelves 24 × 48 in?
A 48 × 96 in sheet is exactly two 24 in strips wide and two 48 in pieces long, but only if the blade removes nothing. With an example 1/8 in kerf:
Two 24 in shelves across the sheet need 24 + 1/8 + 24 = 48-1/8 in. The sheet is 48 in.
Two 48 in shelves along the sheet need 48 + 1/8 + 48 = 96-1/8 in. The sheet is 96 in.
Largest four equal shelves: (48 − 1/8) ÷ 2 = 23-15/16 in by (96 − 1/8) ÷ 2 = 47-15/16 in.
Kerflio's planner, given four 24 × 48 in shelves, placed three on the first sheet (each 48 in long across the full sheet width, which needs no cut along that edge) and the fourth on a second sheet. Given four 23-7/8 × 47-7/8 in shelves, it placed all four on one sheet, using 99.2% of it.
This example uses 23-7/8 × 47-7/8 in, 1/16 in under the maximum each way, to leave a little for a factory edge that is not quite straight. Measure your sheet; some panels are made slightly under the nominal 48 × 96 in, as the APA plywood page notes for panels sized for spacing (checked 2026-11-14).
Largest four equal shelves: (1,220 − 3) ÷ 2 = 608.5 mm by (2,440 − 3) ÷ 2 = 1,218.5 mm.
This example uses 605 × 1,215 mm. The planner placed all four on one sheet, 98.8% used.
How do the frame sizes follow from the shelf?
Design the frame around the shelf you can actually cut.
Each cleat runs from the front face of the front post to the back face of the back post, so it equals the overall depth, which is the shelf depth.
The shelf spacing does not appear in the cut list. It only decides where you screw the cleats, so you can settle it at assembly.
What is the complete cut list?
| Part | Qty | Imperial length | Metric length | Material |
|---|---|---|---|---|
| Post | 4 | 72 in | 1,800 mm | 2×4 (38 × 89 mm) |
| Cleat | 8 | 23-7/8 in | 605 mm | 2×4 (38 × 89 mm) |
| Rail (front and back) | 8 | 44-7/8 in | 1,139 mm | 2×4 (38 × 89 mm) |
| Part | Qty | Length × width | Material | Grain / rotate |
|---|---|---|---|---|
| Shelf | 4 | 47-7/8 × 23-7/8 in (1,215 × 605 mm) | 3/4 in nominal (18 mm) plywood | Rotate allowed |
How many 8 ft boards does the frame need?
Parts: 4 × 72 + 8 × 23-7/8 + 8 × 44-7/8 = 838 in.
838 ÷ 96 = 8.73 boards, so at least 9.
Then fit the parts, with an example 1/8 in kerf between neighbours:
- One post and one cleat: 72 + 1/8 + 23-7/8 = 96 in exactly. Four boards give the four posts and four cleats, with nothing left over.
- Two rails: 44-7/8 + 1/8 + 44-7/8 = 89-7/8 in. Four boards give all eight rails, each leaving about 6 in.
- Four cleats: 4 × 23-7/8 + 3 × 1/8 = 95-7/8 in. One board gives the last four cleats.
Nine boards, which is also the minimum by length. Kerflio's linear planner found the same: 20 of 20 pieces on nine 96 in boards, 97.0% of the length used.
Total: 4 × 1,800 + 8 × 605 + 8 × 1,139 = 21,152 mm. 21,152 ÷ 2,440 = 8.67, so at least 9.
Post and cleat: 1,800 + 3 + 605 = 2,408 mm, leaving 32 mm.
Two rails: 1,139 + 3 + 1,139 = 2,281 mm.
Four cleats: 4 × 605 + 3 × 3 = 2,429 mm.
The planner used nine boards, 96.3% of the length.
How is the shelf sheet broken down?
Four equal shelves come from one rip and two crosscuts, plus trim cuts to bring each piece to size. With a 1/8 in kerf on a 48 × 96 in sheet:
- Rip the sheet at 23-7/8 in. The other strip is 48 − 23-7/8 − 1/8 = 24 in wide, so it gets a 1/8 in trim to match.
- Crosscut each strip at 47-7/8 in. The other piece is 96 − 47-7/8 − 1/8 = 48 in long, so it gets a 1/8 in trim too.
- Check all four shelves against each other before assembly. Small differences show up as rocking on the cleats.
Rip at 605 mm: the other strip is 1,220 − 605 − 3 = 612 mm, trimmed to 605.
Crosscut at 1,215 mm: the other piece is 2,440 − 1,215 − 3 = 1,222 mm, trimmed to 1,215.
Those trims are where the 1/16 in (or few millimetres) of margin goes. If a factory edge is chipped, take the trim from that side. The breaking down plywood sheets guide covers handling a full sheet, and guillotine cuts explained shows why edge-to-edge cuts like these suit a panel saw or track saw. Follow your saw's manual for the cutting itself.
What if a board is shorter than 96 in?
The post-and-cleat pattern has no margin in the imperial version. If a board has a split end that you must cut off, or measures a little under 96 in, the cleat will not fit beside the post. The planner will then show that cleat as unplaced instead of quietly shortening it.
Ways out, in order of least change:
- Measure every board and enter the real usable length.
- Shorten the posts slightly, for example to 71-3/4 in. Nothing else in the cut list depends on post length.
- Buy one extra board for the cleats that do not fit.
The metric version has 32 mm to spare on those boards, which absorbs a trimmed end.
What mistakes are common on shelving units?
- Cutting shelves at the nominal half-sheet size and finding the last one short by a kerf.
- Designing the frame first and the shelf last. Start from the shelf you can cut, then size the frame.
- Cutting rails to the overall width. They sit between the cleats, so they lose a post and a cleat at each end.
- Using nominal 2 in thickness in the arithmetic. The overall width becomes 47-7/8 + 4 = 51-7/8 in on paper and 50-7/8 in when built.
- Assuming every 8 ft board is 96 in and square at both ends.
For how many pieces a single board gives in general, see how many pieces from a board.
Can I plan this in Kerflio?
The four shelves fit the free sheet planner easily. The frame is 20 pieces, more than the 12-piece limit of the free linear planner, so check it in two runs: posts and cleats (12 pieces) and then the rails (8 pieces). Planned separately, the runs cannot share a board, so the total may come out higher than the combined nine. The Android app's full access plans all 20 together.
Frequently asked questions
How deep can the shelves be if I use the whole sheet width?
With a 1/8 in kerf, two shelves across a 48 in sheet can be at most 23-15/16 in deep. With a 3 mm kerf on a 1,220 mm sheet, 608.5 mm.
Can I use OSB for the shelves?
For the cut list, yes. Measure its real sheet size and thickness, and plan it as its own material.
Do I need rails under every shelf?
This example uses a front and back rail under each shelf to stiffen it and tie the ends together. Leave them out and the cut list drops eight parts, but the unit has less holding it square.
Can I make the unit taller?
Yes, but the post-and-cleat boards stop working: a longer post leaves less than a cleat length on a 96 in board. Rerun the plan with the new sizes.
How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.