What are the design assumptions?

This is an example design for a freestanding wardrobe or a carcass that will be built in. It shows how tall parts change the planning, so adapt the sizes to your room.

  • Sides run from floor to top, 2000 mm. A 2000 mm part fits within a 2440 mm sheet length. A taller carcass needs longer sheets or a joint; see sheet sizes by country.
  • Top and bottom sit between the sides. The bottom is raised on two kick rails 80 mm tall, front and back, with the front rail flush with the side edges.
  • A centre divider splits the inside into two bays: a hanging bay with a fixed hat shelf and a rail, and a shelf bay with four adjustable shelves.
  • The back is a 6 mm panel applied to the rear edges, so the sides are 580 − 6 = 574 mm deep.
  • Two full overlay doors with example gaps of 2 mm at the outer edges and top, and 3 mm between the doors.
  • Panels measured at 18 mm, from 2440 × 1220 mm sheets. An example UK retail listing sells 18 mm birch plywood at that size; measure what you buy.

Source: MKM, Birch Faced Plywood 2440mm x 1220mm x 18mm (example retail listing), checked 2026-11-14.

How is each part size worked out?

Interior width = 1000 − 2 × 18964 mm
Bay width = (964 − 18 divider) ÷ 2473 mm

The top and bottom span the interior width: 964 × 574 mm. The kick rails are 964 × 80 mm.

Divider

The divider runs from the top of the bottom panel to the underside of the top panel.

Worked example: divider height

Top of the bottom panel: 80 kick + 18 = 98 mm above the floor.

Underside of the top panel: 2000 − 18 = 1982 mm.

Divider height = 1982 − 98 = 1884 mm. Depth 574 mm, the full side depth.

Shelves

The hat shelf in the hanging bay is fixed, so it spans the bay exactly: 473 × 574 mm. The four adjustable shelves get 1 mm clearance at each end and a 24 mm setback at the front: 473 − 2 = 471 mm long and 574 − 24 = 550 mm deep. Clearance and setback are example values.

Doors and back

Door width = (1000 − 2 − 2 − 3) ÷ 2496.5 mm
Door height = 2000 − 80 kick − 2 top gap1918 mm

The back covers the full width from the top down to the underside of the bottom panel: 1000 × (2000 − 80) = 1000 × 1920 mm.

How do you plan the hanging space?

The rail is hardware, so it is not on the sheet cut list, but it decides where the hat shelf goes. Measure, do not guess:

  • Width of your widest hanger, compared with the interior depth. In this example the inside is 574 mm deep, and the doors close in front of that.
  • Length of your longest garment on its hanger, plus the hook and the rail bracket. That sets the height of the rail, and the hat shelf sits above it.
  • Width of the hanging bay, 473 mm here. Change the divider position if you need more hanging length than shelf space; the two bay widths must still add up to 964 − 18 = 946 mm.

Moving the hat shelf or the divider does not change any part size except the bay widths, so settle the bays before you write the list.

What does this look like in inches?

With imperial panels the fractions get awkward quickly, which is a reason to design from the inside out. With 3/4 in nominal panels measuring 23/32 in:

Worked example: starting from the outside

Overall 40 in wide: interior 40 − 2 × 23/32 = 38-9/16 in.

Bays: (38-9/16 − 23/32) ÷ 2 = 18-59/64 in each. Nobody wants to mark 59/64.

Worked example: starting from the bay

Choose 19 in bays.

Overall width = 2 × 19 + 3 × 23/32 = 40-5/32 in.

Top, bottom and kick rails: 2 × 19 + 23/32 = 38-23/32 in.

An 80 in tall carcass fits a 96 in sheet. The method for the divider, shelves and doors is the same as the metric version; use the fractions and units guide to check your sums.

What is the complete cut list?

Metric version, millimetres
PartQtyLength × widthMaterialGrain / rotate
Side (L and R)22000 × 57418 mm plywoodGrain along 2000, do not rotate
Top and bottom2964 × 57418 mm plywoodRotate allowed
Divider11884 × 57418 mm plywoodGrain along 1884, do not rotate
Hat shelf (fixed)1574 × 47318 mm plywoodRotate allowed
Adjustable shelf4550 × 47118 mm plywoodRotate allowed
Kick rail (front, rear)2964 × 8018 mm plywoodRotate allowed
Door (L and R)21918 × 496.518 mm plywoodGrain along 1918, do not rotate
Back11920 × 10006 mm panelGrain along 1920, do not rotate

Fourteen pieces of 18 mm plywood. If you band shelf and door edges, take the band off these sizes first; see edge banding allowance.

Why does it need four sheets when area says three?

Worked example: area check

Sum of the 14 part areas: 7,850,604 mm².

7,850,604 ÷ 2,976,800 = 2.64 sheets, so at least 3.

Area cannot see shape. Five parts are long enough that each needs a full-length strip of a sheet: two sides, the divider and two doors. Across a 1,220 mm sheet, with an example 3 mm kerf, they pair up like this:

  • Two sides: 574 + 3 + 574 = 1,151 mm. Leaves a strip 1,220 − 1,151 − 3 = 66 mm wide.
  • Divider and one door: 574 + 3 + 496.5 = 1,073.5 mm. Leaves 143.5 mm.
  • One door alone, or two doors: 496.5 + 3 + 496.5 = 996 mm. Leaves 221 mm.

Five long parts at two per sheet take three sheets, and one of them carries a single long part. The space left for the nine short parts is short ends (2,440 − 2,000 − 3 = 437 mm beside the sides, 2,440 − 1,918 − 3 = 519 mm beside the doors), narrow strips, and one wide strip beside the single part.

Worked example: a hand attempt at three sheets

Sheet 1: both sides. The 437 × 1,220 mm end takes the two kick rails.

Sheet 2: both doors. The 519 × 1,220 mm end takes the hat shelf and one shelf: 574 + 3 + 550 = 1,127 mm across.

Sheet 3: the divider in a 574 mm strip, with one shelf in the 553 mm left at its end. A 643 mm strip beside it takes the top and bottom (964 + 3 + 964 = 1,931 mm) and one shelf in the 506 mm left.

Result: one adjustable shelf, 471 × 550 mm, has nowhere to go. The 437 mm end is too short and the strips are 66 and 221 mm wide.

That attempt does not prove three sheets are impossible, and Kerflio does not promise the best possible layout either. Its planner placed 14 of 14 parts on 4 sheets, 65.9% of the sheet area used, with the fourth sheet holding three shelves and a free area of about 1,492 × 1,220 mm. Use that space for drawer parts, cut the odd shelf from the offcut of another job, or plan a second unit with it. The back takes one 6 mm sheet.

What mistakes are common on tall carcasses?

  • Designing a part longer than the sheet. Check the tallest part against the sheet you can buy before anything else.
  • Forgetting the room to stand it up. Tipping a 2000 mm tall, 580 mm deep carcass upright needs about √(2000² + 580²) = 2,082 mm of height. Build tall units on their back where they will stand, or check the ceiling first.
  • Locking the shelves against rotation. Only the sides, divider and doors need it in this example.
  • Splitting the bays from the overall width without the divider thickness.
  • Assuming floors are level. Plan for packing or adjustable feet under the kick rails; the cut list does not change.

Can I plan this wardrobe in Kerflio?

The carcass is 14 pieces, two more than the 12-piece limit of the free sheet planner. You can check the eight carcass parts without the shelves in the web planner, then the shelves against the leftovers. The Android app's full access plans all 14 together and can save the leftover to its offcut library. See offcut inventory.

Frequently asked questions

Can I make the wardrobe deeper?

Yes. Deeper sides and divider still pair two across a 1,220 mm sheet up to (1,220 − 3) ÷ 2 = 608.5 mm wide. Past that, each tall part needs its own strip and the sheet count goes up.

Why is the divider shorter than the sides?

It sits between the bottom and top panels, so it loses the plinth height and two panel thicknesses: 2000 − 18 − 98 = 1884 mm.

Do the doors have to be 18 mm plywood?

No. If you make them from another material, move them to their own group. Taking the doors out of this group changes how the long parts pair up, so replan.

Is the back one piece?

Here yes: 1000 × 1920 mm fits on a 1220 × 2440 mm sheet. A wider wardrobe would need a joined back.

How this page was made: written by Certloom Learning from the sources cited on the page and arithmetic checked in code; layout counts come from the Kerflio planning engine. Kerflio is an independent tool. Check sizes against your own material and equipment.